1. If the input voltage 32VP.P and f=50HZ, sketch the output of the circuitshown below.TDD.10k=3 V=4 V2. Determine Vo20 ySiI kaPrecedIRAQI UNIVERSITY

NOTE: "Since you have asked a multiple question, we will solve first question for you. If you want…

Answered: If the input voltage 32VP.P and f=50HZ,…

Engineering

Electrical Engineering

If the input voltage 32VP.P and f=50HZ, sketch the output of the circuit shown below. 10kA TD D. 10k 3 V -4 V SITY

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4. For the transistor in the figure shown below, the parameters are ß = 100 and VÀ = ∞. a. Design the circuit such that lEQ = 1mA and the Q-pt is in the center of the dc load line. b. If the peak-to-peak sinusoidal output voltage is 4V, determine the peak-to-peak sinusoidal signals at the base of the transistor and the peak-to-peak value of Vs. If the load resistor R₁ = 1kQ is connected to the output through a coupling capacitor, determine the peak-to-peak value in the output voltage, assuming vs is equal to the value determined in part (b). Vcc=+10 V www Rs = 0.7 kΩ Cc www RB RE vo
For the circuit shown in figure. FindAvAiZoZi
5, a) Determine Vdsat when ID=.5 mA. b) Determine Kn when ID = 0.5 Amps. (Show your work!) c) Determine VTN. (Show your work!) d) Vgs Consider the circuit and corresponding graph, shown below. ID (mA) 0.60 0.50 0.40 0.30 0.20 0.10 0.00 0 0.5 Vds 1 1.5 2 2.5 Vds 3 3.5 4 4.5 5 -Vgs = 1V - Vgs = 1.1V - Vgs = 1.2V - Vgs = 1.3V
Vcc=15V Q1: BC237 Rc 3.6kQ or BC238 B=200 VBE(on)=0.7V R1 110KQ Rs Cci 1000 4.7µF Cco 4.7µF R2 ·27kΩ RE 1.2kQ RL 12kΩ Vs Rin Rout Figure 1. Common-emitter amplifier. 2)
I'll give a thumbs up. Pls. help me. ASAP
N-channel Mosfet compared to P channel mosfetWhich of the following is true?A) It is faster.B) It has a lower input impedance.C) It has a lower noise level.D) none
........ (Figure-1) R. RB= 380kN,Rc= 1kN B = 100, VBB = Vcc=12V RB ww Vec CC ......... I, V CE СЕ V ВЕ BB Q-1-b) Describe briefly the input / output characteristics and application of Common Emitter BJT Configuration
This is about BJT. I'm looking for the Ic, and Ib of this circuit.
TOPIC: BIPOLAR JUNCTION TRANSISTOR (BJT)
Design a buck-boost converter with the specifications: Vin = 28 V, in %3D the range [24V,32V], Vout=12 V (with opposite polarity to Vin), load power in the range [0, 120 W], such that to operate in CCM for any line and load value. Select a switching frequency of 100kHz. Choose C= 1.8mF, 25V, 2.5mQ.
O d. 22.42deg A transistor is used as a switch and the waveforms are shown below. If the losses during conduction period, turn on period, turn off period and off period are given: Pon = 13.87 W, P, = 38 W, Poff = 40.66 W, P. = 0 W, then the total average power losses due to the collector current is equal to: Select one: O a. 56.99W Ob. 35.78W O c. 71.5W O d. 92.54W TOSHIBA
Using LTSpice, simulate the circuit below, use 2N3904 for the transistor. Part ! DC simulation: Measure VCE and Ic. Use .op for the simulation cmd. Remove all capacitors and input signals first. Part 2 AC simulation: Connect all capacitors now and apply an AC signal at the input with an amplitufe of 1mV and a frequency of 1kHz. Determine the Voltage gain of the circuit by dividing Vo with Vin. Show the output for both the DC and AC analysis. Take a screenshot of the circuit and the output voltages and waveforms. Paste in a word file, write your answers, then save as pdf. 50 kΩ Σ 20 0,5 ΚΩ wwwh 9 Vcc=20 V Ca=1 µF = Cc₂ Cg=50 μF 5.6 kn B=100 Ca IST • 3.3 ΚΩ 5 ΚΩΣ CE