If the current waveform in Fig. 1 is applied to a 20-μF capacitor, find the voltage v(t) across the capacitor. Assume that v(0) = 0. [Ans: v (t) = 100 t²kV, 100 (4t-t²-2)kV, 0 < t < 1 ] 1

Q: Bus bar system with the simplest design is A20 a) duplicate bus bar b) single bus bar with…

A: We need to select correct option for simplest bus bar .

Q: Design a synchronous counter that count 0,1,2,3,4,5,6,7,8,9,0 ... using Karnaugh map.

A: Counting Sequence is 0-1-2-3-4-5-6-7-8-9-0 repeats on,, This is MOD-10 Counter.

Q: 5.26 An unloaded generator with a pre-fault voltage 1 pu has the following sequence impedance: Z, =…

A: Given, An unloaded generator with pre-fault voltage, E = 1 pu Zero sequence impedance, Zo=j0.15 pu…

Q: In a 10-trunk circuit, there are 180 calls in one hour. The average holding time per call is 2…

A: Given: In a 10-trunk circuit, there are 180 calls in one hour. The average holding time per call is…

Q: The binary equivalent of the decimal number 12 is __________.

A: Binary code- Binary code is a code which is written in form of 0 and 1 for representing numbers or…

Q: Measurement CT should not saturate by design during fault True False

A: the measurement CT and the protection CT design is different in terms of the rating

Q: AMoving to another question will save this response. uestion 8 Which of the following is the phase…

A: In this question we need to choose a correct option.

Q: Explain how the tie line power deviation can be incorporated in two area systems block diagram?…

A: Interconnected power system provides economy and continuity of power supply. Consider two areas are…

Q: Line to line to line fault is an asymmetrical type of fault in power system which occurs very…

A: Given Line to line fault is an asymmetrical type of fault in power system.

Q: What are creepage and clearance distance in electrical hardware components?

A: Creepage and clearance distance are important parameters to consider when designing and selecting…

Q: can you please further explain the peak power delivered to r2 portion. thank you

A:

Q: Question: In mid point type stepdown cycloconverter during positive half cycle of the supply voltage…

A: We need to tell about direction in cyclo converter .

Q: The implementation of a 4-1 multiplexer NOT following the hierarchical design technique and using…

A: A multiplexer is a combinational circuit that selects one of several input signals and forwards it…

Q: Match the following questions with correct answer. Use of double circuit lines: Choose.. In case of…

A: In this question we will write about double circuit line uses..

Q: Please briefly describe the fault characteristics of DC microgrids and compare different typical…

A: We have to describe the fault characteristics of DC microgrids and compare different typical…

Q: signal is used to prevent other system bus masters from gaining access to the local bus.

A: LOCK: This yield pin demonstrates that other framework transport bosses will be kept from acquiring…

Q: AMPS cellular standard _______  as the multiple access method to minimize interference

A:

Q: 3) Draw the schematics of a HVDC and of a HVDC light, compare the systems evidencing advantages and…

A: HVDC means high voltage direct current is a method of electrical power transmission which uses…

Q: 1 List the logic gates names that have been used in the given combinational logic circuit. 2. Write…

A: Introduction: There are different kinds of logic gates like AND, OR, NOT, EX-OR, EX-NOR, NAND, and…

Q: Underground cables are least affected by lightning. Select one: O True False

A: Underground cables are least affected by lightning .

Q: What are the main resion inside System verilog simulation in time step?

A: Verilog is Hardware Description language . The memory and array declaration in Verilog is static in…

Q: Keeping the opposition to current as low as possible in electrical bonding systems is necessary so…

A:

Q: Differentiate MCB and RCD and Explains its purpose in an installation?

A: MCB is an electrical switch designed for automatically working to protect the electrical circuit…

Q: Output voltage can be varied to compensate for load changes by manually adjusting the

A: Output voltage can be varied to compensate for load changes by manually adjusting the   Fill in the…

Q: Compute using 4 decimal places and use scientific notation when necessary Box all final answers.…

A: Source:Ean=120∠0° v;Ebn=120∠-120° v;Ecn=120∠120° vZan=Zbn=Zcn=0.1+j1.5 ΩLine Impedance:Zline a=Zline…

Q: Option 2: A-P1-load -N

A:

Q: The system values are given below. The bus 1 voltage after fault =6.18 p.u. The bus 2 voltage after…

A: Following Data is given in the question V1 = 6.18 p.u. V2 = 2.54 p.u. Y12 =3.25 p.u. Fault Current…

Q: The negative sequence voltage generated is equal to

A:

Q: Consider a binary sequence with a long sequence of 1s followed by a single“0" and then a long…

A: The given binary sequence is We need to draw the split-phase (Manchester) signal of the given…

Q: B 4. 7411 ZAS 10 1 7411 OLI FIGURE 3

A:

Q: 5- What is meant by Present Serviceability Index? How is it calculated?

A: Present serviceability index : Present serviceability index is a permanent measure which is mainly…

Q: The system values are given below. The bus 1 voltage after fault =3.35 p.u. The bus 2 voltage after…

A:

Q: Approximately 75 percentage of the fault are either _____ or permanent LG Faults. a. LLG b.…

A: There are different types of faults occurs in transmission line.     1) LLG   When two lines come…

Q: don't use third party content 1716. Explain the concept of hierarchical attention in funnel…

A: Hierarchical Attention in Funnel Transformers :Hierarchical attention in funnel transformers…

Q: Explain in your own words the operation of signalling system-7 with a neat diagram and write any two…

A: SS7 Stands for signalling system-7, it is a set of telephony signaling protocols those are…

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.