If the chain is released from rest from the position shown. determine the angular velocity of the pulley after the end B has risen 2 ft. The pulley has a weight of 55 lb and a radius of gyration of 0.375 ft about its axis. The chain weighs 6 Ib/ft. Express your answer to three significant figures and include the appropriate units. ANSWER:

If the chain is released from rest from the position shown. determine the angular velocity of the pulley after the end B has risen 2 ft. The pulley has a weight of 55 lb and a radius of gyration of 0.375 ft about its axis. The chain weighs 6 Ib/ft. Express your answer to three significant figures and include the appropriate units. ANSWER:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Need only a handwritten solution only (not a typed one).
The uniform 35-lb bar with attached 11-lb wheels is released from rest when = 64°. If the wheels roll without slipping on the horizontal and vertical surfaces, determine the magnitude of the angular velocity of the bar when 9 = 42°. Each wheel has a centroidal radius of gyration of 6.1 inches. A Answer: @= 8" 6.0' B rad/sec
Gears A and B of mass 15 kg and 56 kg have radii of gyration about their respective mass centers of ka = 80 mm and kg = 150 mm. (Figure 1) Figure M = 10 N - m 0.1 m 0.2 m 1 of 1 Part A If gear A is subjected to the couple moment M = 10 N·m when it is at rest, determine the angular velocity of gear B when t = 5 s. Express your answer to three significant figures and include the appropriate units. WB = Submit μÀ Value Provide Feedback 3 Request Answer Units ?
stion 5 The 20-kg wheel has a radius of gyration ko = 400 mm where O is the center of the wheel. If the wheel is subjected to a moment, M = (2t) N.m, where t is in seconds, determine its angular velocity when t- 4s starting from rest. Assume the wheel is subjected to rotation only (no translation). OA 16.0 rad/s B. 10.0 rads oc 8.0 rad/s 0 5.0 rad/s
solve 30-40 minutes hand written asap..i'll rate
The centroidal mass moment of inertia ofthe pulley assembly is 20 ft-lb-s2. Determine (a) the tension in the cordsupporting 161-lb block , (b)the tension supporting the 322-lb block, and (c) the angularacceleration of the pulley system .Hint: Determine first the direction ofmotion, i.e. will block A move up ordown?
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A uniform slender rod of length L = 900 mm and mass m = 4 kg is suspended from a hinge at C. A horizontal force P of magnitude 75 N is applied at end B. A Ja B C P Determine the corresponding angular acceleration of the rod. The corresponding angular acceleration of the rod is rad/s² O.
A drum of radius r, = 4 in. is mounted on a cylinder of radius r, = 6 in. A cord is wound around the drum, and its extremity D is pulled to the left with a constant velocity of 6 in./s, causing the cylinder to roll without sliding. Determine: 1. The angular velocity of the cylinder. 2. The velocity of the center of the cylinder A. riin. 12 in D. Select one: AW-3rad/s; and VA = 12 in/s: O B.w 4 rad/s; and VÀ = 16 in/s. 2 rad/s and VA=6 in/s. OD.W. 5 rad/s and VA = 25 in/s 9:15 PM ) A ENG 77-Apr-2021
Determine the rotational inertia of the device shown below. R = 0.50 m, r = 0.2 m, the mass of the box is 30 kg. When Fapp= 176 N, the box has an upward acceleration of 0.8 m/s2. Use g = 9.8 N/kg.
The system is made up of the 1-m, 6.7-kg uniform rod AB and the two uniform disks (each of 0.10 m radius and 2.2 kg mass). If the system is released from rest when 0- 55", when rod AB has just become horizontal, determine the angular velocity of rod ABin rad/s. Assume the disks roll without slipping. Your answer must include 2 places after the decimal point. Please pay attention: the numbers may change since they are randomized. Take g= 9.81 m/s?. 1m
The 4.8-kg rod AB is attached to a collar of negligible mass at A and to a flywheel at B. The flywheel has a mass of 16 kg and a radius of gyration of 180 mm. If the angular velocity of the flywheel is to be the same in the position shown and when point B is directly above C, determine the required value of its angular velocity in the position shown in the figure. 720 mm B 240 mm The required value of angular velocity of the flywheel is rpm (Click to select)
Answer within the day with written solutions please!