If only 5% of the supplied power to a cable reaches the output terminal, the power loss in the cable, in decibels, is (round off to nearest integer) -—————' Enter Your Answer... Check

Q: Design a synchronous counter that count 0,1,2,3,4,5,6,7,8,9,0 ... using Karnaugh map.

A: Counting Sequence is 0-1-2-3-4-5-6-7-8-9-0 repeats on,, This is MOD-10 Counter.

Q: Describe how attenuators are used to adjust TV signals power and also reduce interference.

A: According to the question, we need to describe how attenuators are used to adjust TV signal power…

Q: What is a multipath channel? why is a multipath channel frequency selective?

A: Multipath channel Multipath channel (MPC) authorizes to code single transmission group for…

Q: What is matched termination?

A: In this question we discuss what is matched termination.

Q: How many select lines would be required for an 8-line-to-1-line multiplexer? O a. 1 O b. 8 О с. 2 O…

A: The number of select lines required for the N:1 Multiplexer is given by  Log2 (N). N is the the…

Q: How much power savings would be achieved with new system compared to existing system. Consider the…

A: The new system voltage was reduced by 30%.The new system frequency was reduced by 20%.We need to…

Q: I need a complete experience about Dispersion Compensation technique for the optical  fiber…

A: We need to explain about Dispersion Compensation technique for the optical fiber communication using…

Q: What is SMD in the electrical field?

A: In the electrical field, a Surface Mount Device (SMD) is a type of electronic component that is…

Q: This question addresses the outcome: Design combinatorial and sequential circuits (C6) You are…

A: Requirement:   Design modulus 5 up/down counter using JK Flipflop.   Firstly determine the…

Q: 4- A 100 MHz clock signal clocks a synchronous digital circuit. The longest delay allowed for a…

A:

Q: Can you redo this again? The answer should be typewritten, thanks. Provide the following: Step 1.…

A: Asked to find transfer function by using Mason's rule

Q: 3. Suppose that EAX = 00001000H, EBX = 00002000H, and DS = 0010H. Identify the addressing modes and…

A: The table is given below:

Q: What can you say/perspective about National Electrical Code?

A: The National Electrical Code (NEC) was created to protect people and property from the risks posed…

Q: Briefly describe Depolarization field?

A: Depolarization is an electrochemical process in which polarisation in any material or polarisation…

Q: A major disadvantage of nonzero switching of power to a load is ____. A. possible damage to the…

A: A major disadvantage of non zero switching of power to load is  Option:B   RF noise generation.

Q: Determine whether the circuit presented below is forward-biased or reverse-biased. State your…

A: Analog electronics problem. Look below for the explaination...

Q: c) Cutting forces should be kept constant during machining operations to prevent changes in spindle…

A:

Q: What is the difference between blocking assignments and non- blocking assignments ? What is the…

A: Verilog is a hardware description language. The memory and array declaration in Verilog is static.…

Q: select one quickly Synchronous counter is ........... than asynchronous counter. a) faster, b)…

A: Synchronous counter is counter which clock input for each flip flop given at a time and output of…

Q: A frequency modulation system has a rated system deviation of 12.7 kHz and a maximum allowable…

A:

Q: b. x₁(n) = -28(n + 1) − 38(n − 1) +58(n − 2); - x₂ (n) = 58(n) - 38(n + 1) + 28(n + 2) - 48(n − 1) +…

A:

Q: Why we use the modulation ?

A: The explanation is as follows.

Q: Modulation and Demodulation: 1. Define detection process? 2. What are the different types of…

A: Modulation and demodulation: Modulation is the process of encoding information in a transmitted…

Q: Choose the correct Answer: The difference in the propagation delay between the fastest and slowest…

A: delay skew is the difference between the propagation delay on the fastest and slowest pairs in a…

Q: ST 3000 Transmitter by Honeywell Draw block diagram of the Transmitter – name major parts

A: We have given ST3000 Transmitter by Honeywell Draw the block diagram of the Transmitter

Q: Find Inverse Laplace Transform: 4s + 8 4s +8 Y1(s) = Y2(s) = s². (s+1)(s² + 2s +5) (s+1)(s² + 2s+ 5)…

A:

Q: Give the reason for the following statements: 1) Using a Venturi flow sensor makes the measurement…

A: Any liquid coulmn upto a certain height has some potential energy. Venturi flow meters are devices…

Q: How many select lines would be required for an 8-line-to-1-line multiplexer? a. 1 O b. 2 O. 8 O d. 3

A: Multiplexer is also called as MUX. These are used to select one input at a time from many input…

Q: Is this signal periodic or aperiodic? Please show working.

A: Given:a signal, ,To find:whether the given signal is periodic or aperiodic?

Q: 1. SP=F000H; after PUSH BX, what is the value of SP? _____________  2. BL=00, after instruction DEC…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: What is ampere circuital law?

A: This law gives the relation between the magnetic field and the current which created the magnetic…

Q: output for an input of a. eut) b. cos 2m

A:

Q: How would you define the "race," a typical synchronization error?

A: We have to define the "race," a typical synchronization error?

Q: 4:1 multiplexer hasA. 2 select linesB. 4 select linesC. 8 select lines.

A: 2n×1multiplexer has 2ninputs and n multiplexer.

Q: what are the two techniques for circuit switching? D) what is the cause of the propagation delay?

A: Given  We need to enumerate Two techniques for circuit switching and the cause of propagation delay.…

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.