If oil has kinematic viscosity 4 x 105 m2/s, andspecific gravity is 0.9, flows from the upper tolower reservoir at a rate of 1870 liter/min in the 23cm smooth pipe (roughness is zero).Given that the minor head losses coefficient ofentrance 0.5, bend 0.32 and outlet 1.9.Use g 9.81 m/s².Elevation = ?60m-2<Elevation= 130 m7m130mDetermine the discharge in m³/s, Q. Determine the discharge in m³/s, Q.Determine the flow velocity, v.Determine the Reynolds Number, ReDetermine the friction factor.Determine the total head losses (major andminor).What is the elevation of the oil surface in the upperreservoir (point 1)?

Answered: Image /qna-images/answer/273f7529-99d8-47df-bb37-2de4d23cb508.jpg

If oil has kinematic viscosity 4 x 105 m2/s, and specific gravity is 0.9, flows from the upper to lower reservoir at a rate of 1870 liter/min in the 23 cm smooth pipe (roughness is zero). Given that the minor head losses coefficient of entrance 0.5, bend 0.32 and outlet 1.9. Use g = 9.81 m/s². Elevation= ? 60 m Elevation =130 m 7 m 130 m Determine the discharge in m³/s, Q.

If oil has kinematic viscosity 4 x 105 m2/s, and specific gravity is 0.9, flows from the upper to lower reservoir at a rate of 1870 liter/min in the 23 cm smooth pipe (roughness is zero). Given that the minor head losses coefficient of entrance 0.5, bend 0.32 and outlet 1.9. Use g = 9.81 m/s². Elevation= ? 60 m Elevation =130 m 7 m 130 m Determine the discharge in m³/s, Q.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1-The storage tank shown below is to be used to supply a community such that the pressure at Point B…

A: Q= , , D = 600mm=0.6m , L = 1000mTo Determine: Water Depth(h) in the tank that will meet the design…

Q: 1. A 30 cm well completely penetrates an artesian aquifer. The length of the strainer is 25 m.…

A: Given Radius of influence 350 mDiameter 30 cmLength 25 mPermeability 45 m/dayDrawdown 4 mTo find out…

Q: A reservoir is shown in Figure E4.6a. (a) Draw the flownet. (b) Calculate the flow rate. (c) How…

A: Solution: Given Data k=1×10-9 ft/s

Q: A well is installed in a unconfined aquifer. Determine the drawdown (ft) at the well if: the radius…

A: R=500ft H=95ft

Q: The pressure heads are measured at two sections in a pipeline and are found to be 8.3 m at point A…

A: Step 1: Step 2: Step 3: Step 4:

Q: DAM 30 FT FLOW T = 20 FT SAND IMPERVIOUS ROCK B = 240 FT The total length of the dam shown is 800…

Q: As shown in the figure compute the amount and location of the vertical and horizontal components of…

A: Given data,radius is 7.5mL=10mFINDAmount and location of vertical and horizontal component

Q: A dam of 21.5 m height and has free board of 1.5 m. A flow net is constructed containing following…

A: A dam of 21.5 m height and has free board of 1.5 m.Number of potential drops = 12Number of flow…

Q: 1. For the flow net shown in the figure below, if the datum is selected at the downstream water…

Q: uid mechan

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Question

If oil has kinematic viscosity 4 x 105 m2/s, and
specific gravity is 0.9, flows from the upper to
lower reservoir at a rate of 1870 liter/min in the 23
cm smooth pipe (roughness is zero).
Given that the minor head losses coefficient of
entrance 0.5, bend 0.32 and outlet 1.9.
Use g 9.81 m/s².
Elevation = ?
60m
-2<
Elevation
= 130 m
7m
130m
Determine the discharge in m³/s, Q.

Determine the discharge in m³/s, Q.
Determine the flow velocity, v.
Determine the Reynolds Number, Re
Determine the friction factor.
Determine the total head losses (major and
minor).
What is the elevation of the oil surface in the upper
reservoir (point 1)?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem 1: A pipeline 300 m long discharge freely at a point 50 m lower than the water surface at intake (Figure 1). The pipe intake projects into the reservoir. The first 200 m is of 350 mm diameter and the remaining 100 m is of 250 mm diameter. (a) Find the rate of discharge assuming f= 0.06. If the junction point C of the two sizes of pipe is 40 m below the intake water surface level, find the pressure head. L₁, D₁, f AZ1 C L2, D2, f T 122 -V₁
A town is planning to develop a new water supply from an aquifer. Two observation wells installed 1000 ft apart have respective head of 300 ft and 295 ft above a common datum. Within the aquifer, hydraulic conductivity (Kn) 25 ft/day. The aquifer has a mean width (w) = 2 miles and thickness (b) = 200 ft. Estimate the volumetric flow %3D %3D %3D rate through the aquifer in cubic feet per day. Well 1 h= 300 ft 1000 ft Well 2 h = 295 ft AQUIFER 200 ft suturation 2 miles
Two reservoirs are connected through a 900 m long, 0.5 m diameter pipe, which has a gate valve. The pipe entrance is sharp (loss coefficient = 0.5 ) and the valve is half-open (loss coefficient = 5.5). The head difference between the two reservoir is 10 m. Assume the friction factor for the pipe as 0.03 and g = 10 m/s2. The discharge in pipe accounting for all minor and major losses is?
Two Water flows from reservoir A to reservoir B through two pipes as shown below. Determine 1) thedischarge in the pipe, 2) the pressure at point P. Assume α = 1.0 at all locations and neglect any minor headloss
Problem #2: For the 50-mm-diameter siphon drawing oil (SG = 0.82) from the oil reservoir the head loss from point 1 to point 2 is 1.50 m and from point 2 to point 3 is 2.40 m. Find the discharge of oil from the siphon and the oil pressure at point 2. SG 2.00 m Oil (sp gr=0.82) 5.00 m 50-mm-diameter siphon D= .5 4₁ = 3-7 h = 1.5+ 2.4 3.9 На + hp t hp = H up =
Oil (SG = 0.8, y = 0.010 Pa-s) flows through a 10-cm smooth pipe (length: 100 m) at a discharge of 0.010 m³/s, what is most approximately the head loss? O 7.21 m O 5.23 m O 1.28 m O 2.55 m
Water is being pumped at a steady rate of 500 gpm from a 12in diameter well. Thewell draws water from an unconfined aquifer. The height of water in the aquifer in the equilibrium statebefore pumping is 100ft, and the drawdown at the well at steady state pumping is 40ft. The hydraulicconductivity of the aquifer determined from a pump test is 0.02ft/min. Determine the radius of influence.
ELEV. = 75m 1 ... A L = 1700m D = 400mm f = 0.02 ELEV. = 15m C D L = 3500m D = 800mm f = 0.03 A three reservoir problem shown in the figure with their corresponding length and diameter. Determine the discharge in all pipes. (A) Q1 = 0.431 m3/s, Q2 = 0.295 m3/s, Q3 = 0.726 m3/s (B) Q1 = 0.327 m3/s, Q2 = 0.458 m3/s, Q3 = 0.785 m3/s Q1 = 0.295 m3/s, Q2 = 0.413 m3/s, Q3 = 0.708 m3/s (D) No answer among the choices E Q1 = 0.346 m3/s, Q2 = 0.402 m3/s, Q3 = 0.748 m3/s (F) Q1 = 0.286 m3/s, Q2 = 0.519 m3/s, Q3 = 0.805 m3/s 2 ELEV. = 40m B L = 1900m D = 500mm f = 0.025 3
The velocity in this channel is 0.9 m/sec. The Froude number is 6.73 m y=1.5 m 5 m 0.82 .a O 0.25 .b O None of these .c O 0.57.d O
- once answered correctly will UPVOTE!!