if each square measures 35.04 square meters and A= 9.05m, B=5.8m, C=4.33m, D=9.92m, E=2.73m, F=4.06m, G=3.26m, H=4.42m, I=8.63m, J=5.07m, K=6.95m, L=2.14m and M=5.68m, detrmine the volume of the excavation in cubic meter.

Q: 120m by 120m lot is to be divided into 9 equal square sections. The elevations of the ground surface…

A:

Q: A 120m by 120m lot is to be divided into 9 equal square sections. The elevations of the ground…

A:

Q: 100 mm 150 mm

A:

Q: The triangular gate shown in the figure below is hinged at the B and rests on a smooth floor at A,…

A: Answer 13.1) When vertex at A Draw free body diagram of forces acting on the gate as shown below F…

Q: 3 ft y=x y 3 ft ******** x^3 9

A:

Q: Determine the magnitude and the direction angles of a vector (V) and draw in the space provided if…

A:

Q: Show your neat and complete solution Given a closed compass traversed (use three decimal places)…

A:

Q: Determine the coordinates of the centroid of the trapezoidal area shown. Assume a = 310 mm, b = 570…

A:

Q: A square has sides 5 cm smaller than the sides of a second square. The area of the larger square is…

A: Given, A square has sides 5 cm smaller than the sides of a second square. The area of the larger…

Q: The diameter of a circle is equal to the one side of a cyclic quadrilateral. Let the one diagonal of…

A:

Q: Find the volume to be excavated if the ground surface is to be leveled to elevation 5m.

A: Givendata: The elevations of the ground surface at each corner of the square section are given as:…

Q: what is the value of ang e values on the drawing Law of Sines or Cosines?

A:

Q: Situation 3: The magnitudes of the three forces acting on the plate are T₁ = 100 kN, T2= 80 kN, and…

A: Given data

Q: Can you explain the shear force part why we needed to divide it by 2.6

A:

Q: For the cross section shown below, with dimen- sions given in in., determine the moments of inertia…

A: since ,it is symmetrical about y-axis.therefore,x¯=0 from the figure,position of centroid of the…

Q: Hydraulic radius is the ratio of wetted perimeter to area. TRUE or FALSE?

A: Explanation : Hydraulic radius is a term in open channel flow which is used to measure the…

Q: 2. The following equations were established for a study area. T=40+ 489x, -0.004x,-02-0.017.…

A: Number of observations used in setting up the equations is 53.

Q: . Determine the centroidal coordinates of the cross-sectional area shown. Please show complete…

A:

Q: where did you get the values of tp=17.27 & do=24 ??

A: Given question,  How to get values of tp and do = ?

Q: Analyze the beam 4P (kN) 2P (kN/m) 80° 3m 3m 4m 3m

A:

Q: AP (xx) 1 (x - q) 9. = A 4 de 1 a 2 a on sixes i ag

A:

Q: Two triangles are similar. Triangle 1 has side a = 15 and side b = 8. Triangle2 has side B = 30. How…

A: Given Data: Sides of Triangle 1 are a=15 and b=8. Sides of Triangle 2 are B=30.

Q: 16. Can the cross-section resist demands of My=97.2 kip-ft and P=648 kip? YES / NO (CIRCLE ONE)…

A: Solution: Concrete column analysis: GIven: fc = 5500 psi;  fy= 60 ksi  no. of bars = 8 DIa. of bars…

Q: why is delta B=delta C=0.015 and not 0.15.

A:

Q: A 120m by 120m lot is to be divided into 9 equal square sections. The elevations of the ground…

A:

Q: In order to determine the equivalent permeability of a site approximately, a colored paint is poured…

A:

Q: 58. Given the data below determine the area of the cross section if the base is to be 10m wide. a.…

A:

Q: Find the volume to be excavated if the ground surface is to be leveled to elevation 3.3m.

A:

Q: Y

A:

Q: What is FB in N? What is the angle FB in degrees? What is FA in N?

A:

Q: The solid shaft is subjected to the distributed and concentrated torsional loadings shown, where T =…

A:

Coordinate Geometry of Survey

Coordinate geometry (COGO) is a method of inserting surveying or engineering data into geographic information system (GIS), computer-aided design (CAD), or mapping software. These data can be collected on the proposed construction site using standard surveying techniques and instrumentation or may be taken from existing maps, engineering plans, drawings, or records. Data gathered on the site includes coordinates of points, bearings, and distances between points. The data are noticed and noted through conventional surveying procedures, like a traverse or layout measurement series and it can be either digital or non-digital. The maps and plans are inclusive of boundaries, divisions, and other components, and these features are shown with coordinate values, the lengths, offset distance, and bearings between them.