If a total of 33 MHz is allocated to a particular FDD cellular telephone system which uses two 25 KHz simplex channels to provide full duplex voice and control channels, compute the number of channels available per cell if a system uses a) 4-cell reuse, b) 7-cell reuse, and c) 12 – cell reuse. If 1 MHz of the spectrum is reserved for control channels, determine an equal distribution of control and voice channels for all the three cases

If a total of 33 MHz is allocated to a particular FDD cellular telephone system which uses two 25 KHz simplex channels to provide full duplex voice and control channels, compute the number of channels available per cell if a system uses a) 4-cell reuse, b) 7-cell reuse, and c) 12 – cell reuse. If 1 MHz of the spectrum is reserved for control channels, determine an equal distribution of control and voice channels for all the three cases

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter25: Television, Telephone, And Low-voltage Signal Systems

Section25.1: Television Circuit

Problem 15R

See similar textbooks

Similar questions

Explain how adaptive modulation works in communications systems using an illustration?
Q3: A radio frequency signal was received with signal to quantization power ratio of 39dB and mathematical model of 4cos28.4nt * 10°, calculate 1- The number of bits every second. 2- The bandwidth and signaling rate. 3- The quantization noise power if the transmitted signal power of 0.04 watt.
3. In fixed channel assignment strategy, each cell is allocated a predetermined set of, a) Voice channels b) Control channels c) Frequency d) base stations
To implement 8-to-1 line multiplexer using two 4-to-1 line multiplexer(MUX): O a. The third selctor is connected to the enable line of the first and second MUX. O b. Only the enable line of the first MUX must be connected dirictly to the enable for the second MUX. O c. The third selctor is connected to the enable line of the first MUX which is connected through inverter to the enable of the second MUX. O d. All inputs lines for the first mux must be connected to the input lines for the second mux.
Determine the Emmision Classification 2. Single sideband full carrier single analog channel telephony
3) DIGITAL COMMUNICATIONS II course.
DO NOT COPY FROM OTHER WEBSITES Correct and detailed answer will be Upvoted else downvoted. Thank you!
Consider a CDMA system where transmitter A has the code 101010 and transmitter B has the code 111001. Assume that 1 is represented by +1V and 0 is represented by -1V. Show that the two CDMA codes (after mapping them to voltages) are orthogonal to each other. What is transmitted if A sends a bit of 0 and B sends a bit of 1? What did A and B most likely transmit if the received word is “-1 -1 -1 +1 +1 +1”?
Given that the base address is FoH. 1. Create a new asm project “Lab2_Q1.asm". Assume that port A of 8255A PPI is connected to 8085. Write assembly code to send the value of FFH to FoH. Enter a delay of 2 ms for each transmission.
Question 2
Please help me answer number 2. Please show a CLEAR and READABLE solution/s. Thanks!!! The course subject is Fundamentals of Electronic Communications. NOTE: ANSWER LETTER D ONLY!!!
In an FDMA-based multiple access system, each user is assigned an 80 kHz channel for full-duplex communication. There are 1000 channels in the system.Depending on the information given above, if the initial frequency of the frequency spectrum used by the FMDA system in one direction is 1000 MHz, which of the following is the correct spectrum of the bond's spectrum.A1.000.000 KHz - 10000.080 KHzB1000.000 KHZ - 1.000.040 KHzC1.000.000 KHZ - 1.040.000 KHzDNoneE1.000.000 KHZ - 1.020.000 KHZ