If a lowering dc dc converter input voltage is 100v, the output voltage should be 60v. Switching frequency 10khz coil value is determined as l = 3mh. In this case, what should be the c capacity value of the output filter in order for the output voltage fluctuation to be 10V. a)100mf b)100uf c)10uf d)10mf e)10nf

Q: The nominal output voltage of a certain regulator is 8 V. The output changes by 2 mV when the input…

A:

Q: In order to light a LED: O send a HIGH signal and this will be written in the Loop function send a…

A: In order to light a LED what we will do in a program : options : Send a HIGH signal and this will…

Q: For the Phase-Shift oscillator, determine the oscillator frequency C, = C2 = C3 = C = 0.001 µF R2 =…

A:

Q: The positive peak value of output waveform for the given circuit diagram is. Bias voltage is 2 V,…

A:

Q: . What is problem with this circuit? * Vcc I Rc 1kQ - Vout + Vin O No AC signals at the input O The…

A:

Q: For the given circuit, what is the minimum peak value of the output waveform if the input waveform…

A: Negative Clamper Circuit: A Negative Clamper circuit is one that moves the output signal to the…

Q: Design a zener regulator to meet these specifications: 1. Load voltage is 6.8 V 2. Source Voltage…

A:

Q: What should be the input peak voltage (in volts) in the given circuit below to produce a dc output…

A:

Q: Design a Buck Converter with the Following Features. Input Voltage = 50 V Output Voltage = 20 V…

A: Buck Converter:  It is a type of DC-DC converter where input voltage is being stepped down to get…

Q: An op-amp Colpitts oscillator (Figure 4) has C1 = 750 pF, C2 = 2500 pF and L = 40 µH. Calculate the…

A:

Q: Briefly explain about Resonant CCM Boost Converter, zero current switching (ZCS) and zero voltage…

A: Zero Voltage Switching (ZVS) operates when the voltage is zero, as opposed to Zero Current Switching…

Q: design a triangular wave oscillator with oscillation frequency of (50 KHz) and triangle wave has…

A: Given design requirements of triangular wave f=50 kHz Vpp=6 V Vcc=Vsat =18V

Q: 2- For the circuit given below : Vin is a sine wave Vinpp=18 V and Vref=-0.7 V, Assume Vsat=+12V…

A: we need to draw the input and output waveform of the given opamp

Q: A level transducer has an output range of 0 to 10 V. For a 3-meter level, the output voltage for a…

A:

Q: Question 1. Design a Boost Converter circuit by drawing according to the Values given below. Input…

A:

Q: Determine the period and frequency of oscillation for an astable multivibrator with component values…

A: The astable multivibrator generate square wave. It doesn't require any external triggering pulse.…

Q: 4.4 A boost-regulator has an input voltage of 5 the average output voltage of 15 V. The duty cycle…

A: Given a boost regulator has, Input voltage, Vin=5 V Average output voltage, Vo=15 V

Q: Q2. Consider the following RISC-V loop: (i) (ii) (iii) (iv) (iv) (v) (vi) (vii) DONE: add x12, x11,…

A: Since you have posted a question with multiple subparts, we will solve the first three subparts for…

Q: In a single phase full wave AC voltage controller, the firing angle of the SCRS is equal, then the…

A: In a single phase full wave ac voltage controller, the firing angle of the SCR is equal  The average…

Q: Q 2. Find the values of Rand C for the phase-shift oscillator in Figure 2 so that the oscillation…

A: According to question we have to find the value of R and C.

Q: Find the value of Cext for the following oscillator, cutoff frequency =25kHz 45,5 V RESET Vee DISCH…

A: The given 555 circuit is: Cutoff frequency, f=25 kHz

Q: Q2) for the astable multivibrator cct shown Determine: 1. frequency of oscillation 2. duty cycle 3.…

A: To determine the frequency of oscillations, Calculate the time period of individual transistors Sum…

Q: In step-down regulator in Figure below, calculate the output voltage if the switching frequency is…

A: Given data : Switching frequency fsw=76.923KHz   Discharging time of capacitor=7μsec…

Q: Q4. a) b) Figure 7 shows a phase-shift oscillator. Explain briefly how the phase shift required for…

A: the phase-shift oscillator circuit shown in Figure 7.a) Achieving Sustained Oscillation with Phase…

Q: 2. Draw and explain the difference between clipper circuit and clamper circuit output waveform

A:

Q: For the clamper circuit shown below, Find and Plot the output waveforms and Check the essential…

A:

Q: If input voltage is 18Vpeak-peak, plot the output waveform. Assume Ideal approximation.

A:

Q: Vhat is the output peak voltage during the positive alternation of the input ignal for the circuit…

A:

Q: Given the following circuit, determine: (a)The secondary peak voltage. (b)The minimum average…

A: NOTE- As per the rules we can answer only 3 sub-parts, please post the remaining sub-parts as the…

Q: the time delay that must be provided by each stage in order to achieve an oscillation frequency of…

A:

Q: What are saturation current and cutoff voltage in given figure? Also draw Q point beta =80 & 120.…

A: By applying KVL to the 10V circuit, Let consider a Silicon diode  So, VBE=0.7 V…

Q: öslg äbäi Find the value of Cext for the following oscillator, cutoff frequency =25kHz +5.5 V R 1.0…

A: The given 555 Astable multivibtrator is Cutoff frequency=25kHz

Q: What should be the input peak voltage (in volts) in the given circuit below to produce a dc output…

A:

Q: For the following circuit, Vo D1 Vi choose the correct voltage transfer characteristic curve. Assume…

A:

Q: 2. Determine the frequency of oscillation for the circuit of the figure below: Vout 20 k 10 k 50 k…

A: In this question we will find frequency of oscillation...