If a deflection of 13 degrees in a pressure transducer is produced by apressure of 3 bar, the scale deflection of the instrument is:0.231 bar/degree.0.231 degree/bar.O 4.333 degree/bar.O 4.333 bar/degree.Not all of the above.The resolution of a digital voltmeter that has 16 – bit accuracy with therange of 250V is equal to:3.5mv.1.7mv.1.8mv.1.9mv.Not all of the above.

1) given deflection in degree= 13 Pressure is 3 bar 2) no of bits n= 16 V range = 250v

If a deflection of 13 degrees in a pressure transducer is produced by a pressure of 3 bar, the scale deflection of the instrument is: 0.231 bar/degree. 0.231 degree/bar. 4.333 degree/bar. 4.333 bar/degree. Not all of the above. The resolution of a digital voltmeter that has 16 – bit accuracy with the range of 250V is equal to: 3.5mv. O 1.7mv. 1.8mv. 1.9mv. O Not all of the above.

If a deflection of 13 degrees in a pressure transducer is produced by a pressure of 3 bar, the scale deflection of the instrument is: 0.231 bar/degree. 0.231 degree/bar. 4.333 degree/bar. 4.333 bar/degree. Not all of the above. The resolution of a digital voltmeter that has 16 – bit accuracy with the range of 250V is equal to: 3.5mv. O 1.7mv. 1.8mv. 1.9mv. O Not all of the above.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the circuit below Junction voltage is 0.7V the +ve and -ve peak of the output waveform is +10V Vin 0 -10 V t 41₁ O +4.3,-4.3 O +5.7, -5.7 O +10.7, -10.7 O +7.3, -7.3 R₁ ww 1.0 ΚΩ D₁ 5 V Diodes are IN914. D₂ 5 V * out
In order to design an square wave oscillator with 50% duty cycle of the period of 1 second. Specify the values of R1, R2, and C1, C2 in Astable Multivibrator using 555 timers.
6
Please answer fast I'll rate you sure....,.,.
Choose the correct answer
1. Table Q2 shows output measurement of a voltmeter under two sets of conditions. The voltmeter was calibrated at the temperature of T = 25 °C. Table Q2: Voltmeter output measurement. Voltage reading at T-50 °C UT UTM 12.5 UTM & UTMUTM 24.7 49.0 37.1 UTM & UT TM UTM UTM Determine zero drift and zero drift coefficient when it is used in 50 °C TM & UTM UTM 49.3 TM & UTM TM & UTM TM & UT Voltage at T = 25 °C 12.2 24.4 UT UTM 36.8 &UTMUTH UTM UTM UT UTM 8 UTM & UT UTM TMUTenvironment. UTM
An RC filter stage (R = 42 Ω, C = 220 µF) is used to filter a signal of 30 V dc with 6 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 200-mA load. Also calculate the ripple of the filtered signal applied to the RC stage.
3)please solve! Will upvote
Compute the complete (input & output) characteristics of n-channel JFET in the form of curves.The JFET has typical parameters as IDSS=12mA and VGS(off)= -5V.
Is the small signal equivalent circuit for this diagram correct? How do we add cg and Cs?
if you design differentiator to differentiate input signal varies in frequency between 1 KHz and 20 KHz then find. Cutoff frequency=.......... 01000 O2000 03000 04000
subject : electronics engineering