If a 200 N force F1 is applied to the piston with the 4 cm diameter, what is the magnitude of the force F2 that can be resisted by the piston with the 10 cm diameter? Neglect the weights of the .pistons

Q: could you pls provide part D and E

A:

Q: Derive an espression for the height of propell governor

A: Deriving expression for proell governor considering proell governor taking moment about point…

Q: what would be the order of operations to make this part in the least amount of time and how would…

A: The order of operations to make this part in the least amount of time and how would you hold the…

Q: find dy 2 dx Y=4+ gill=TLX, Ccosut 4

A:

Q: Write short note on compression ratio

A: compression ratio

Q: the bending endurance limit for AISI 1080 steel shaft is Select one: a. 307.5 MPa. b. 250 Мра с. 450…

A: The bending endurance limit for AISI 1080 steel shaft can be given by - Se = 0.5×Ultimate strengthSe…

Q: Determine the distance and resultant of the five parallel forces acting on the rocker arm of the…

A:

Q: Find the two-dimensional temperature distribution T(r,z) under steady state condition. Where, To=20…

A:

Q: A cast-iron gear with 100-mm effective diameter and t = 40-mm hub engagemen length is to transmit a…

A: Given: R - 10 mm t - 40 mm T - 120 N.m ro - 50 mm Ec - 100 Gpa Es - 200 Gpa f - 0.16  v - 0.3 To…

Q: 150 N 35° 4 120 N 30° 80 N 40° X

A:

Q: hat is formula for friction factor?

A: Friction factor: This is also called the Darcy friction factor. It is used in the Darcy-Weisbach…

Q: 01/ Give the dimensions for the hole and shaft for the 12 mm electric motor sleeve bearing (pump);

A: Given:Basic size given for motor sleeve bearing=12 mm

Q: Convert to cis form

A: Conversion to cis form.

Q: 7) Given the ISO metric hexagon socket screws in the figure; select the correct name of the head…

A: For question number 7 the correct answer is option b. As the first figure is of cap screw and second…

Q: In order to find the force in DJ we will have to make a new cut. Cut through IJ, DJ, and CD. The…

A:

Q: How pilot tube works?

A: The pitot tube is a simple device that is used to measure the flow velocity with no moving parts.

Q: Differen bending neaf possible ach t

A: for solution refer below images.

Q: ) What machine that has a shaft with a minimum of three (3) [bearings, pulley, sprocket, gear,…

A: given:

Q: Draw the assembly views of the following G Clamp from a front view and top view. Provide a standard…

A: To Draw the assembly views of the following G Clamp from a front view and top view.

Q: Convert from decigrams to pounds 4dg->1B Transfer from Dream to Desigram dcixss->dg Convert from…

A: 1. Convert from decigram to pound 1 dg = 14535.92371 dg = 0.0002204622621847756 lbso,4 dg = 4…

Q: 150 N r= 25 mm Calculate the equivalent moment at O, taking into account the values given in the…

A:

Q: How can we determine the displacement with truss?

A: Virtual work method: This method is a very important method which s used to find the slope as well…

Q: Find the farce f the brep Show all wort

A:

Q: *ind Acodn al 4 and D. Ay he beem.

A:

Q: The rotation angle of the joints is still needed.

A:

Q: 4. (Ef-1 X¡)^2 =D1

A: Sigma indicates sum of ^ indicates power.   In order to solve this, the following equation should be…

Q: Problem 6.131 Determine the general expression of the acceleration of the piston C as a function of…

A: Write the given data.

Q: ) Given: h,- 3620 k/Ya, V. : 45mls ト、 V, - 75 mls Vq 120mls (caleulate the work Dore by seam) Stea…

A: Given data,  h1 = 3620 kJ/kg  h2 = 2800 kJ/kg  V1= 75 m/s  V2= 120 m/s  Assumptions-  z1=z2 and heat…

Q: Name the 2 types of axial loading?

A: Two types of axial loading are tensile and compressive stress. Both kinds of stresses arise within…

Q: Q 13. A frame is said to be 'Perfect frame, if it followS certain relation betvoen number of members…

A: Perfect frame will not change when it is subjected to load with help of perfect number of members…

Q: ?What are the type of vibration in circular wood saws and fluid pipe, and why

A:

Q: Define the term Shaft Design?

A: Given Shaft design To find Definition

Q: Calculate the minimum length of a parallel key for a gear which is to be mounted on a 60 mm diameter…

A:

Q: A hydraulic punch press is capable of delivering 2,000kPa pressure on its platen from its 250mm…

A: Given: A hydraulic punch press is capable of delivering 2,000kPa pressure on its platen from its…

Q: Alm that He Cafle

A:

Q: hich one of the following Cast iron is produced by the heat treatment of White cast iron?

A: 1)   Option b) Malleable   cast iron Malleable  cast  iron are relatively very soft and can…

Q: 4. This diagram shows the front-end of a machine that has a bucket at the tip. The total weight of…

A: solution Step 1 -:                Draw FBD of bucket and analyze tanθ =0.32.5θ=6.843°sin θ =0.12cos…