x Online Final Exam-EETE2 102 Elechttps://lms.act.edu.om/mod/quiz/attempt.php?attempt-5693&cmid-982&page=D2 nstion 13If a 2 mV signal produces a 2 V output, what is the voltage gain?yetweredO 0.001ced out ofO 0.011000ag questionO 100on 14Find the value of a current gain of a common emitter transistor, if the current gain of a common base transistor is 0.9.etred900d out of9.O 90questionO 0.9اكتب هنا ل لبحثB.acerPauseInsertF12PriScF10F11BreakScF8F9SysRqF6F7NumLkF3F4F5

2mV signal produce output Voltage 2V Gain? If the current gain of CB = 0.9 Current gain for CE?…

If a 2 mV signal produces a 2 V output, what is the voltage gain? 0.001 O 0.01 1000 O 100 Find the value of a current gain of a common emitter transistor, if the current gain of a common base transistor is 0.9. 006 0 06 O О 09

If a 2 mV signal produces a 2 V output, what is the voltage gain? 0.001 O 0.01 1000 O 100 Find the value of a current gain of a common emitter transistor, if the current gain of a common base transistor is 0.9. 006 0 06 O О 09

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

If the dc emitter current in a certain transistor amplifier is 4.31 mA, the approximate value of r'e (in ohms) is
Given the transistor circuit with beta as 100. Answer the following items below.1. Base Current 2. Collector Current 3. Emitter CurrentShow complete solution
The collector current is 6.41 mA when the base current is 56 mA. What is the alpha of the transistor?
7) Consider the circuit shown below. Assume that the transistor is in saturation, VTN = 1.0V and Kn = 6.4mA/V². Determine Vo if Vin = 2V. Show your work! Vin 5V 3000 Vo 625
In a transistor if ß = 100 and collector current is 10 mA, then IE is .......... O 120 mA O 100 MA O 100.1 mA O 110 mA
Given the circuit in the Figure, determine the emitter current and the collector-base voltage VCB. Assume the offset voltage is V₁ = 0.6V. 20 ΚΩ ww 20 V 39 ΚΩ 20 V
n a certain voltage-divider biased npn transistor, VB is 4.67 V. The dc emitter voltage, in V, is approximately
For the circuit sown, using the transistor * values of: B = 200, lc = 4mA and lb = 20uA, find the value of the Base resistor (Rb) required to switch the load "ON" when the input terminal voltage exceeds 2.5v. Vcc Flywheel Diode RB w + Vin ( 90kΩ 30kQ 9kQ 0.07ΚΩ IB R 20 Relay Ic Vce Ov Load Output
Q/ In DC machines, the external characteristics are plotted between Ans/ 1- Eg vs load current 2- Vt vs Ia 3- Eg vs Ia 4- Vt vs load current
Which region in the transistor is ? very thin and lightly doped Emitter O Base Colletor O
Can this question be solved as soon as possible?Or a maximum of 10 minutes
The figure below shows a three-stage circuit using two-supply emitter bias. What are the collector-to-ground voltages (VC) for each stage? Rc1 Rez Rc3 • 10 ΚΩ • 10 ΚΩ • 10 ΚΩ Vin RE1 RE2 • 20 ΚΩ • 20 ΚΩ RB₁1 · 33 ΚΩ RB2 33 ΚΩ RB3 33 ΚΩ Vcc +15 V to Yout RE3 • 20 ΚΩ VEE –15 V