If a 10-A current source has an internal resistance of 100 ohms, what is the current flow from the source when the terminal voltage is 200 V?

Q: voltmeter

A: Resistance in parallel- 1Req=1R1+1R2+1R3+........... Resistance in series- Req=R1+R2+R3+...........

Q: • In the source room you connect a battery of 20V to terminals A and B, A being the point of higher…

A: Here, we have given two rooms, one of them is the source room and the other one is the sink room.…

Q: Three 47.1 ohm resistors and three 17.1 H inductors are all in series with a 37 volt battery and a…

A:

Q: Correct me if i am wrong I have studied different formula formula for saturation current.

A: Both are correct.

Q: he figure the current in resistance 6 is ig = 1.36 A and the resistances are R1 = R2 = R3 = 2.50 N,…

A: The solution can be achieved as follows.

Q: We want to make a resistivity measurement. How should we connect the probes of the multimeter? Drag…

A: a multimeter is a portable device that can be used to take various electrical measurements like,…

Q: If we use 5000 µF, we can get a very low ripple voltage. But this is so bad and this a disadvantage,…

A: According to the given question we are using a 5000 micro farads capacitance , then there is a…

Q: When you connect a voltmeter to read a dc voltage   a. polarity is not important b. connect the…

A: In this question,  We need to choose the correct options When you connect a voltmeter to read a dc…

Q: 12 V 2 kn 3 kn 4 mA 1 kn 3 kn 2 kn 1o

A: The voltage drop across 2k ohms is determined for the above-shown circuit diagram

Q: Determine the voltage across R1 in the figure below, if the source is 10 volts, the Zener is 6.8…

A:

Q: In the figure the current in resistance 6 is i6 = 1.33 A and the resistances are R₁ = R₂ = R3 = 1.56…

A: According to the question, for the given circuitWe need to find emf of the battery.

Q: E www R

A: We need to find out voltage across resistor for given circuit .

Q: what is the equivalent resistance Rab

A: This question belongs to circuit theory . It is about calculation of equivalent resistance of the…

Q: What is the greatest voltage that can be applied across a -W, 2.7-MN resistor without causing it to…

A:

Q: How much is the eurrent, I, at each of the following points? a. Point A b. Point B c. Point C d.…

A: Since there is no other way...The current will flow through the given loop According to law of…

Q: VCC = 5V IN=10 uA R1=2k A В R2=3k GND = OV

A: The question, asks to construct a circuit that has 500 mV at node A and 1000 mV at node B.

Q: Three resistors of 5, 10, and 15 ohms respectively are connected in series with a 24V source…

A: In this question we will find current through 5 ohm..

Q: 680 N R2 R3 B C 3.3 kfN 1.5 kN Vs 15 V 820 Ω RL 2.2 kN Ic Figura 1

A: Here it is asked to find the potential difference between two points A and C. Here KVL has been used…

Q: A circuit component carries a current of 2.4 amperes and has a voltage drop of 10 volts across it.…

A: Given that,             current I= 2.4A             voltage drop Vd=10V             resistance R=?…

Q: VT= 10 V A R₁ 150 $2 R₂ 15 $2 R3 1052 B + Lo

A:

Q: 6. The equivalent total resistance in the circuit in Figure 1 is 2200 E=7V- 4700 1000. 100. 3300…

A:

Q: A 0 – 150 voltmeter has a resistance of 2000-ohms per volt.  It is desired to change this voltmeter…

A:

Q: a 12 volt source with an internal resistance of 1.2 ohm is connected across a wire wire wound…

A:

Q: 7. An electric drier requires 360W and draws 3.25A. Find its operating voltage.

A: According to guidelines we need to solve only the first question. According to the question we have…

Q: Analyse Figure Q2.1 to determine the voltage with respect to ground at points A, B, C and D. Assume…

A:

Q: Convert the following figure to current source and findI source? R1 1.2K 身 RL1 27.6V 2.5K, 230 mA O…

A: The given circuit is:

Q: R1 of 90 kilo ohm and R2 of 10 kilo ohm are in series across a 43-volt source. A) Draw the schematic…

A: we need to draw the schematic diagram and need to find the voltage drop at R2

Q: If PMMC meter have internal resistance of 1002 and full-scale range of 1mA. Assume we wish to…

A: Here, Rm=10 Ohm Full Scale range of , Im=1mAIncreased range of, I=2Aso, We have to connect Rsh for…

Q: Please answer it with further explanation. badly need it What are your observations in this table…

A: We know that in a Reverse biased condition diode acts as an open switch(ideally speaking of infinite…

Digital Integrated Circuit Design

Digital IC design is a procedural interaction that involves converting determinations and highlights into computerized blocks, which are then further transformed into basic circuits. A significant number of the imperatives related with advanced IC plan come from the foundry cycle and innovative restrictions.