Answered: If 59.1 mL of 0.178 M hydrochloric acid…

If 59.1 mL of 0.178 M hydrochloric acid requires 12.1 mL of NaOH solution to reach the endpoint, what is the molarity of the NaOH solution? Include three decimal places in your answer.

Introductory Chemistry: An Active Learning Approach

6th Edition

ISBN:9781305079250

Author:Mark S. Cracolice, Ed Peters

Publisher:Mark S. Cracolice, Ed Peters

Chapter16: Solutions

Section: Chapter Questions

Problem 154E

See similar textbooks

Similar questions

Calcium carbonate, CaCO3, can be obtained in a very pure state. Standard solutions of calcium ion are usually prepared by dissolving calcium carbonate in acid. What mass of CaCO3 should be taken to prepare 500. mL of 0.0200 M calcium ion solution?
What kinds of solute particles are present in a solution of an ionic compound? Of a molecular compound?
A student weighs out a 4.80-g sample of aluminum bromide, transfers it to a 100-mL volumetric flask, adds enough water to dissolve it, and then adds water to the 100-mL mark. What is the molarity of aluminum bromide in the resulting solution?
Two liters of a 1.5 M solution of sodium hydroxide are needed for a laboratory experiment. A stock solution of 5.0 M NaOH is available. How is the desired solution prepared?
Stock solutions of HCl with various molarities are frequentlyprepared. Complete Table 14.7 by calculatingthe volume of concentrated, or 12M, hydrochloric acidthat should be used to make 1.0 L of HCl solution witheach molarity listed.
Every pure substance has a definite and fixed set of physical and chemical properties. A solution is prepared by dissolving one pure substance in another. Is it reasonable to expect that the solution will also have a definite and fixed set of properties that are different from the properties of either component? Explain your answer.
Follow the directions for Question 9 for the following pairs of solutions. (a) sodium phosphate and barium chloride (b) zinc sulfate and potassium hydroxide (c) ammonium sulfate and sodium chloride (d) cobalt(III) nitrate and sodium phosphate
Addition of water to concentrated sulfuric acid is dangerous because it generates enough heat to boil the water, causing it to spatter out of the container. For this reason, chemists remember to add acid to water. In a dilution experiment, we calculate the amount of the more concentrated solution that must be measured out. If we place this concentrated solution (Figure 4.7) in the volumetric flask first, then dilute with water, we violate the caution Add acid to water. Describe a safer variation on the method shown in Figure 4.7 that allows the quantitative dilution of concentrated sulfuric acid. Figure 4.7 Preparing a dilute solution from a concentrated solution. (a) Draw the concentrated solution into a pipet to a level just above the calibration mark. (b) Allow the liquid to settle down to the calibration line. Touch the tip of the pipet to the side of the container to remove any extra liquid. (c) Transfer this solution to a volumetric flask. Again touch the pipet to the wall of the flask to ensure complete transfer, but do not blow out the pipet because it is calibrated for a small amount of liquid to remain in the tip. (d) Dilute to the mark with solvent. Frequently, especially with concentrated acids, it is best to have some solvent present in the volumetric flask before you add the concentrated sample.
ssume a highly magnified view of a solution of HCI that allows you to “see” the HCl. Draw this magnified view. If you dropped in a piece of magnesium, the magnesium would disappear, and hydrogen gas would he released. Represent this change using symbols for the elements, and write the balanced equation.
What happens if you add a very small amount of solid salt (NaCl) to each beaker described below? Include a statement comparing the amount of solid eventually found in the beaker with the amount you added: a a beaker containing saturated NaCl solution, b a beaker with unsaturated NaCl solution, c a beaker containing supersaturated NaCl solution. A saturated sodium chloride solution.
An experiment calls for 100. mL of 1.25 M HC1. All that is available in the lab is a bottle of concentrated HC1, whose label indicates that it is 12.1 M. How much of the concentrated HC1 would be needed to prepare the desired solution?
Classify each of the following solutions as saturated, unsaturated, or supersaturated based on the following observations made after adding a small piece of solid solute to the solution. a. The added solute rapidly dissolves. b. The added solute falls to the bottom of the container where it remains without any decrease in size. c. The added solute falls to the bottom of the container where it decreases in size for several hours and thereafter its size remains constant. d. The added solute causes the production of a large amount of solid white crystals.