Identify the several types of lines used in drawing and explain their uses

Q: Figure shows the side view of a tank with a curved gate. The gate width into the page is 18 in. The…

A: Hydrostatic forces The weight of the fluid above the curved surface determines the amount of…

Q: A load of P = 5778 N is acting on member AC. The length of AC is d = 437 mm. The cross-sectional…

A:

Q: A cohesive soil yields a maximum dry density of 1.8 g/cc at an OMC of 16% during a Standard Proctor…

A:

Q: Calculate straight line equation for following Transportation data Road Length, X (km) Number of…

A: Given table is about the road length in Km and number of vehicles on that span of road

Q: Consider the cress section show in the figure b-11n t-2in

A:

Q: A saturated specimen of cohesive soil was tested under drained conditions in a triaxial compression…

A:

Q: If all three supports settle the following amounts: A = 4.0 in., B 2.0 in., and C - 3.5 in.,…

A:

Q: SITUATION. A 9 m high retaining wall is laterally supported at the top and fixed at the base. The…

A:

Q: For the data given in table and taking kor depth and kor period for wheat as 13.5 cm and 4 weeks…

A:

Q: please calculat the angles and complete the following table. Ba A- 零方向 D Survey Survey Targe station…

A: Solution:-

Q: AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 23 kips, w…

A:

Q: What does accretion rate mean, in terms of coast lines?

A: Accretion in terms of coast lines

Q: Two forces P and Q (P > Q) act on the same straight line but in opposite direction, thei sultant is…

A:

Q: seed

A: Force due to weight of glassFg=γ2πrth=2.6×9.81×2π×0.052×0.005×0.1Fg=0.00063765π kNForce due to…

Q: Discuss the following items briefly. 1. How is a meter defined by a standard? 2. Describe how…

A:

Q: Link AB is to be made of a steel for which the normal stress is 310 MPa. Determine the…

A:

Q: Why do you think Hydrographic Maps are referred to the MLLW?

A:

Q: Line Length (m) Bearing N 51° 34' E АВ 22.36 BC 24.84 S 16° 50' W CD 30.00 N 79° 26' W N 77° 06' E…

A: Lattitude and Departure signs:  N-E : Both positive  N-W : Lattitude positive Departure negative…

Q: Explain the effect of metal rolling on grain structure in not more than 10 sentences

A: Rolling is considered in two different forms, i.e, Cold rolling:-  When the metal or the alloy is…

Q: Design a bracket connection to support an end reaction of 200 kN. The. eccentricity of the load is…

A:

Q: A constant-head permeability test was conducted on a soil specimen under a hydraulic gradient of…

A: G=2.65 w=20%

Q: 1. A rectangular open channel of width 5.0 m is carrying a discharge of 100 m3 /s. The Froude number…

A:

Q: Answer: P = %3D Save for Later Using multiple attempts will impact your score. 5% score reduction…

A:

Q: The beam is subjected to a uniform live load of1.2 kN/mkN/m, a dead load of 0.5 kN/mkN/m, and a…

A:

Q: 4. A laboratory analysis of the settlement of flocculated water gave the following results for a…

A:

Q: Settlement that define the life span of structure? Immediate O Primary O Secondary O All of these

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 11 kN applied at A. Assume a…

A: F1=11kN a=250mm b=100mm c=90mm

Q: A sand cone test has been performed in a compacted fill performed on a soil sample. The test results…

A: Sand cone test  The sand cone test is a compaction test used in the field to determine the density…

Q: PROBLEM O3: Given the figure below, (a) determine the flow rate in the siphon shown. Diameter of the…

A:

Q: The extruded plastic shape will be subjected to an internal shear force of V= 385 lb. Dimensions of…

A:

Q: Why are the sum of the anion concentrations and the sum of the cation concentrations are not…

A: Brief concept introduction- Cation ions- These are the positive ions. For water, cations are H+…

Q: A small button placed on a horizontal rotating platform with diameter 0.320 m will revolve with the…

A: Option (C) is the correct answer

Q: Four forces F1, F2, F3 and F4 are being applied on a plate as shown in Figure 1. If your roll number…

A:

Q: agrams for the beam shown below. 10 kN p= 20 kN/m

A:

Q: The four gears are attached to a steel shaft that is rotating at 2Hz. Gear B supplies 70KW of power…

A:

Q: lease show detailed solution: The office building has interior columns spaced 5 m apart in…

A:

Q: Q.68 An activated sludge tank is 30 m long 9 m wide and has liquid depth of 4 m. The influent sewage…

A: Given data- Dimensions of the sludge tank=30m×9m×4mInfluent sewage flow Qo=3.5 MLDBOD So=130mg/LMLSS…

Q: O Seepage velocity is always smaller than O Seepage velocity is equal to the dischar Seepage…

A:

Q: A segment of a generator shaft is subjected to a torque T and an axial force P, as shown in the…

A:

Q: 55 kN 64 kN 100. kN/m A B Im 3m Im R1 FIGURE A R2

A:

Q: 2. Assume the separation for A, B, and C. With the instrument midway between A and B the readings…

A:

Q: Adjust the following angles which were measured at a station O, so as to close the horizon: - 6.…

A: The given data is: Angles with values with their respective weight values are shown above.

Q: The wooden members A and B are to be joined by plywood splice plates that will be fully glued on the…

A:

Q: Determine the stress (in psi) in member BD if the cross-sectional area of the BD is 1.81 in?P = 1662…

A:

Q: A saturated clay stratum of thickness 10 m, bounded on top and bottom by medium coarse sand layers,…

A:

Q: A simple beam with an overhang is subjected to a point load P = 16.5 kN. P A B L -L- If the maximum…

A:

Q: A flat slab is supported on 600 mm dia circular columns spaced 8 m x 6 m apart in both directions.…

A:

Q: . A rectangular open channel of width 5.0 m is carrying a discharge of 100 m3 /s. The Froude number…

A:

Q: A wooden cylinder of a circular section and uniform density with specific gravity 0.6, is required…

A:

Q: Use the moment distrībution method to determine the support reactions for the following beam. The…

A: