22:12←YouJust nowH(8)=input is r(t) = sin(27500t), find the output y(t).is the transfer function of a 2nd order lowpass filter. If R=2500 2, C=0,5 µF, L=1 H andO a. y(t)=0,13sin(2pi500,00t + (-142,34))O b. y(t)=0,26sin(2pi500,00t + (-124,49))O c. y(t)=0,18sin(2pi500,00t + (-135,06))O d. y(t)=0,05sin(2pi500,00t + (-157,26))O e. y(t)=0,08sin(2pi500,00t+ (-151,63))|||+HD+2 || %23O

In this questionWe need to choose the correct option. What is output of the given system. Transfer…

ic is the transfer function of a 2nd order lowpass filter. If R=2500 2, C=0,5 μF, L=1 H and 8+8² +10 input is r(t) = sin(2x500t), find the output y(t). H(s) = = O a. y(t)=0,13sin(2pi500,00t + (-142,34)) b. y(t)=0,26sin(2pi500,00t + (-124,49)) c. y(t)=0,18sin(2pi500,00t + (-135,06)) d. y(t)=0,05 sin(2pi500,00t + (-157,26)) e. y(t)=0,08sin(2pi500,00t + (-151,63))

ic is the transfer function of a 2nd order lowpass filter. If R=2500 2, C=0,5 μF, L=1 H and 8+8² +10 input is r(t) = sin(2x500t), find the output y(t). H(s) = = O a. y(t)=0,13sin(2pi500,00t + (-142,34)) b. y(t)=0,26sin(2pi500,00t + (-124,49)) c. y(t)=0,18sin(2pi500,00t + (-135,06)) d. y(t)=0,05 sin(2pi500,00t + (-157,26)) e. y(t)=0,08sin(2pi500,00t + (-151,63))

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(can you solve it fast?) What filter type is the digital system given transfer function?
3. Find the transfer function H(w) = Vo(w)/V₁ (w) for the circuit shown a. Plot Amplitude and phase spectrum using MATLAB. b. Hat type of the filter (LPF, HPF, BPF, or BSF). Solution: Vin C₁ 36 1 μF R₂ ww 1 KS2 R₁ 1kQ2 + C₂ HH 0.2 μF OUT
Consider the following bandpass filter circuit with C1=0.04uF, C2=D0.01µF, R1=5kN, R2=10k2, R3=20k2. Calculate the lower cutoff frequency F,, and the upper cutoff frequency F, of the circuit. Write your answer in the given space. R1 R1 R3 R3 Vo Vi. R3 C1 R2 Paragraph В I II !!!
For a Low pass filter with a series resistor R = 2 kohms and inductor L = 10 mH with a load resistor RL = 1 kohms, find the: a. transfer function [H(s)] without the load RL b. transfer function [H(s)] with the load RL c. what is the cutoff frequency without the load RL d. what is the cutoff frequency wit the load RL
The transfer function of a first order RC high-pass filter is given below: Draw the circuit representing a RC first [1] order high-pass filter. Clearly show the input and output on the circuit. Proof that the half-power break-frequency of the filter can be described by the equation below (show all steps): fB= 1/2(pi)(R)(C)
15. ..) Given the following Bode plot, what transfer function for H(s) best defines this bode plot? 4018 30d8- 2008. 1000- -10 6 -2018. 14 a 10 d 100 40. (A +100) (+100) (A+109000) -20dB decade C₁ 100 (1 +100,000) 2 (2 +100) (A+1000) 1000 18,000 IF d. 00000 6. 40 (1 +1000) (A+100)ª(2+ 100,000)2 .-40dB de cade 100 (A+1000) (D+100) (A+ 100, 000) d i meg W
Example 06:- For the filter circuit shown, sketch the frequency response and determine the cutoff frequency. 20 a 200 ka 0.002 uF 0.002 u RI = S00 a RO- 2000 AVD= S0,000 10 k2
A band pass filter is to be constructed using RC components that will only allow a range of frequencies to pass above 2 kHz and below 20 kHz. Assuming that both the resistors have values of 10 kΩ, calculate the values of the two capacitors required. Also find the center frequency.
Question 23 What form of filter is seen below? x(n)- O Cascaded form O Parallel form. Direct form. O Lattice form Direct form Il 1/2 D -1/2 D -y(n)
Hello. I'm not sure how to get this practice problem going. Could you help? Thank you. Design 1st-order low-pass filters with cutoff frequency fc = 2 kHz and DC gain of 1 and 5. Inverted or not doesn’t matter. Use a 10 nF capacitor. (i) Draw the circuits, (ii) write the transfer functions and (iii) find the other component values. Don’t make it more complicated than it needs to be!
i need the answer quickly
Supply voltage: V1=10Vpp sin( 2πf ) Undercut frequency fc1=2137.5 Upper cut frequency fc2=34200 Design the RLC Band-Pass Passive Filter circuit? BW=? R=? C=? L=?