i5m 1.5 2 m 20 N 4 m f-2 m- 100 N

Q: For the truss shown in the figure below, assume that the loads are being transmitted to the bottom…

A: Answer Let us first draw ILD for member DI. In order to draw Influence line diagram(ILD) for member…

Q: 2. Use the Muller-Breslau principle to (a) sketch the influence lines for the vertical reaction at…

A: Influence line diagram represents variation of forces at point with respect to placement of load.

Q: (3) The beam is subjected to an internal moment of M = 50 kN.m as shown. Determine the percentage of…

A: parallel axis theorem : The parallel axis theorem, also known as the Huygens–Steiner theorem or…

Q: The block has a mass of 150 kg and rests on a surface for which the coefficients of static and…

A:

Q: A transmission tower is held by three guy wires attached to a pin at A and anchored by bolts at B,…

A: Given  TAB= 110 lb

Q: Draw the influence line for vertical reaction t support B, shear at C and the moment at point D of…

A: We have to find out the ILD for vertical reaction at B, ILD for shear at C and ILD for moment at D.…

Q: A B D E 2.0000 2.0000 2.0000 2.0000

A: When any unit load is passing through the beam, then the reactions or shear forces are presented as…

Q: FB Fc 6 t B 1202 120° 120 4 ftC

A: Determine the force in each chain-

Q: For the beams shown, draw the influence 1ines for the given functions. Use the beam sign convention…

A:

Q: Draw the influence line diagram for bending moment at A for the frame shown. Then using this ILD…

A:

Q: |A B C 3 m 2 m

A: There is a beam AC as follows:(a) Find the line of influence of the vertical reaction at point A.(b)…

Q: Draw the influence line for member BC and interpret the diagram.

A: Solution: Considering the diagram of Truss: Applying a unit load at x from point A and find the…

Q: Question 5 The beam in Figure Q5 is subjected to a uniform dead load of 1.2 kN/m and a single live…

A:

Q: A 2.5' Ay Vc when unit load is egment AC: A Ay = 1- 2.5' C X 10 M 7.5' с Msection = 0 X 10 -Vc + -…

A:

Q: E A В C -8 m- -8 m- -5 m- -5 m-

A:

Q: Determine the magnitudes of tension forces in rope AB, AC and AD for equilibrium of the ring A. (b)…

A:

Q: 2. For the truss shown in the figure below, assume that the loads are being transmitted to the…

A:

Q: A B C mmmmm MI "a" 5.0m "b" D 3.0m E "2" F

A:

Q: determine (a) the tension in the cable, (b) the reaction at C.

A:

Q: Q6) Use the Müller-Breslau principle to sketch the influence lines for the vertical reaction at A,…

A:

Q: A uniform live load of 112 lb/ft and a single live concentrated force of 21 lb are to be placed on…

A: Given data in question  Live load 112 lb/ft Live load 21 lb Dead load 150 lb/ft Span member 27 ft To…

Q: Assume that the loads are being transmitted to the bottom  chord and draw the influence lines for…

A:

Q: A moving vehicle traverse on a bridge supported by the beam below. a. Construct the influence line…

A:

Q: Show the influence lines for forces in bars AL and KJ using EQUILIBRIUM METHOD. Determine the…

A: Given Data: A truck is traveling on a bridge that consists of two trusses:

Q: Assuming that the live loads are transmitted to the bottom chords of the truss, the influence line…

A:

Q: A) The spring AB has a stiffness of k=800 N/m and an unstretched length of 200 mm. Determine the…

A:

Q: d the

A: Draw free body diagram From the above figure At point C, tanθ=21θ=tan-12θ=63.435o

Q: Determine the maximum positive moment of the beam shown. 12KN/m 20KN Ab 6m 2m

A:

Q: 10 kip/ft 50 kip ft A 5 ft 5 ft The simply-supported beam above is subjected to a uniformly…

A: Apply equilibrium condition : ∑MB=0RAY×10-10×5×(52+5)+50=0RAY=32.5 kip

Q: Determine the influence line at point B and t

A: Assuming unit load,     Let the unit load it at x distance from A.    Take moment about c and equate…

Q: Q4 Draw the influence lines for (a) the vertical reaction at B, (b) the shear just to the right of…

A:

Q: Construct the influence line for the shear at point C of the beam in the Figure. A X -4 m 1 C -4 m-…

A:

Q: #2 Draw the influence lines for (a) the vertical reaction at A, (b) the shear at C, and (c) the…

A: Total length = 5+4+7+3 = 19

Q: b

A: Compressive stress is the force that deforms the material in a way that reduces the volume of the…

Q: For the simply supported beam shown, draw influence lines for moment at C (12-ft from support A),…

A: when the unit load at A and B then bending moment at C equal to 0 .and if the unit load at C then…

Q: A bridge truss and a system of moving concentrated load are shown below. The bridge truss: A The…

A: Given: Point loads: P1=25 kNP2=30 kNP3=30 kNP4=50kN To find: ILD for member BC and calculate the…

Q: The overhead electric hoist Crides along a track on the horizontal beam . AB. In addition to the…

A: The resultant force is the sum of all the forces acting on the member. When the force is acting in…

Q: B |A 20 ft 20 ft- 20 ft- Problem: Construct the influence diagram of the bar CI and BC of the truss…

A:

Q: A beam is subjected to the loading condition shown below. Draw the influence lines for: a) the…

A:

Q: For the truss shown in the figure below, assume that the loads are being transmitted to the bottom…

A: Answer  ILD for member DI  Pass a section through member DI as shown below When Unit load is at A…

Q: ence line for the mom

A:

Q: Q1): For the compound beam shown in figure, points C and E are hinges draw: a. the reaction…

A: applying muller Breslau for influence line diagram

Electric Circuit and Components

An electrical circuit or electrical network is a pre-determined pathway to make the electrons flow in the desired direction. The flow of electrons will set up a current flow in the circuit. Normally, the flow of electrical current is opposite to the flow of electrons. An electron is a fundamental sub-atomic particle of an atom possessing a negative charge. To initiate the flow of current and achieve the desired output, the electrical circuit should necessarily be composed of closed pathways. The pathways are made-up of good conductors of electricity such as aluminium and copper.