(b) Figure Q.4b is showing the level control P&ID of a boiler drum system. Theboiler drum is supplying a constant steam flow to the next heat exchange stationwhich is monitored closely by the operator at the site. The water in the boiler hasto be maintained at the set point value in order to ensure that the steam producedis complying the requirement of the heat exchange station. Temperaturemeasurement of the boiler drum is transmitted wirelessly to the control room forcontinuous monitoring of the boiler drum operation.Flow Set pointLYLevelSet pointSteamFeedwaterBoiler DrumFigure Q.4b P&ID of boiler drum system i. Suggest suitable instrument and the function used for item 1, 2, 3 and 4labeled in Figure Q.4b.ii. Explain the operation of each instrument in Q.4b(i).

Boiler drum System- Boiler drum system basically a container which reserve water and steam at the…

Answered: i. Suggest suitable instrument and the…

i. Suggest suitable instrument and the function used for item 1, 2, 3 and 4 labeled in Figure Q.4b. ii. Explain the operation of each instrument in Q.4b(i).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q1 The Zener regulator circuit in Figure Q1 has the following values: R₁ = 0.22 kn, Zener voltage, V₂ = 8 V and the maximum power rating of the Zener diode is 400 mW. In order to maintain this regulator circuit with load voltage, V₁ at 8 V and not exceed the maximum power rating of the Zener diode; determine the: (a) minimum input voltage, Vi min (b) maximum input voltage, Vimax
Discussion : (1) رم طرة what are the advantăge and disadventage of full-wave bridge rectifier cutcuit- calculate ale practically result have been produced (2) Vpeak theortically of voltage output by using реа (3) üG Compare theortically and practically results. (4) What happens do on Vout, if we reversed the four diodes connects . sKetch the Vout in this case . 6. し 2.5 1.48 1.35
Q2/ D'Arsnoval moving coil meter that modified to measure AC current with full wave rectifier, if the forward rectifier resistance is 502 , and its reverse resistance is infinity find: 1. R.. 2. The devise sensitivity for measuring DC voltage. 3. The devise sensitivity for measuring AC voltage Rs E =10 V, rm.s IT Lah2 It =1mA Rahi=400 2 Rhy 100 2 Rm = 500 2
Answer both or else skip the question
DRAW CIRCUIT OF ANALOG TO DIGITAL CONVERTER CIRCUIT. AND EXPLAIN HOW IT WORKS
Q3: bridge rectifier circuit shown in Figure (1), with a forward diode resistance Rd=12, and Rd=0 for a reverse bias. The input voltage of the circuit is 240V and 482 load resistance. Determine: The de load current, the power input efficiency and the PIV rating is required for the diodes. D4 D1 Rd=10 RL=480 Vs Vrms D3 D2 Figure 1
1. Connect the circuit shown in Figure (1), the power supply is set to zero volts. 2. Measure and record in table (1), the forward current in the diode at each level of voltage (Vf). 3. Determine the forward resistance Rf = Vf /If. A I KO E (0-4) V. Figure (1) Vr 0.1 0.2 0.3 0.4 0.5 0.6 0.7 Ir R Table (1)
(a) Digital to analog converter is mandatory requirement in computer. Why?
(c) Figure Q4(c) illustrates a full-wave bridge rectifier used in ac voltmeter circuit. i) Explain the operation of diode D1, D2, D3 and D4. ii) Calculate the value of resistance R., ac sensitivity and de sensitivity. D1 D2 V=20Vme Rs 03 In=1mA R=2502 D4 R=2502 Figure Q4(c) Full Wave Bridge Rectifier
The resistors you can use in the shown below circuit have a maximum power dissipation level of 1W. If the diode has an absolute maximum rating of 1A, and can be modelled with a diode drop of 0.7 V. The maximum output voltage of the variable supply (VIN) is 14 V. What is the minimum value of resistance (R1) that can be used in this circuit? FT Vin R1 Vout
4. a) Based on non-linear circuits: i) Draw a block diagram representing a general oscillator. ii) State the Barkhausen Criterion. b) Consider the Schmitt trigger circuit shown in Figure Q4(a) where the comparator output saturation voltages are given as Vm+ = +15V and Vm- = -12V. R₁ Vow VR R₂ www R₁ Figure Q4(a) i) Calculate the upper and lower threshold voltages at Va if R₁ = 10 k2, R₂ = 20 kn and VR = 3V. ii) Compute the hysteresis voltage, VH. iii) Sketch the transfer characteristics (V₁ vs Va). c) Consider the oscillator shown in Figure Q4(b). i) Name the oscillator type. ii) Deduce the oscillation frequency equation. R₂ Vb Figure Q4(b) V out Z₁
1. What is the function of Voltage and Current Isolator?3. What is the peak output voltage of a three phase three pulse rectifier operating on a line to line voltage ‘X’ V? (Here X= 33)