(i) Write the composition of bleaching powder.(ii) What happens when NaCl is heated with conc. H2SO4 in the presenceof MnO2. Write the chemical equation.

A sample of 70.5 mg of potassium phosphate is added to 15.0 mL of 0.050 M silver nitrate, resulting in the formation of aprecipitate. (a) Write the molecular equation for the reaction. (b) What is the limiting reactant in the reaction? (c) Calculatethe theoretical yield, in grams, of the precipitate that forms.

The digestion of a 0.1159 gram sample of a phosphorous-containing compound in a mixture of HNO3 and H2SO4 resulted in the formation of CO2, H2O, and H3PO4. Addition of ammonium molybdate yielded a solid having the composition (NH4)3PO4·12MoO3 (FW = 1876.3). This precipitate was filtered, washed, and dissolved in 50.00 mL of 0.2000 M NaOH: (NH4)3PO4•12MoO3(s)+26OH-(aq)->HPO42-(aq)+12MoO42-(aq)+14H2O(l)+3NH3(g) After the solution was boiled to remove the NH3, the excess NaOH was back-titrated with 14.84 mL of 0.1626 M HCl to a phenolphthalein end point. Calculate the percent phosphorous (FW = 30.9737) in the sample.

When 15.11 ml of 0.102 M K2SO4 solution reacts with 35.00 ml of 0.114 M Pb(C2H3O2)2, predict the theoretical yield of the solid product.

Fifty food supplement tablets with a total mass of 66.393 g were crushed into powder to analyse the content of FeSO4·7H2O. 2.988 g of the powder were dissolved in HNO3 and heated to convert all the iron to Fe3+. Addition of aqueous NH3 caused quantitative precipitation of Fe2O3·xH2O, which was ignited to give 0.0640 g of Fe2O3. Determine the average weight of FeSO4·7H2O in each tablet.

A 3650-mg sample containing bromate and bromide was dissolved in sufficient water to give 250.0 mL. After acidification, silver nitrate was added to a 25.00 mL aliquot where the resulting precipitate was filtered, washed and then redissolved in an ammoniacal solution of potassium tetracyanonickelate(II) according to the reaction: Ni(CN), + 2 AgBr) → 2 Ag(CN), + Ni? + 2 Br The liberated nickel ion required 26.73 mL of 0.02089 M EDTA. The bromate ion in a 10.00 mL aliquot was reduced to bromide with As* prior to the addition of silver nitrate. The same procedure was followed and the released nickel ion was titrated with 21.94 mL of the EDTA solution. Calculate the percentage of impurity in the sample. Br (79.904) a. 24.45% b.34.38% c. 41.17% d. 65.62%

A 12.63 g sample of calcium ore was dissolved in HCl and gravimetrically analyzed, through the precipitation of calcium into CaC2O4 · H2O. The precipitate was filtered, washed, dried, and ignited at 500 oC until the weight was constant, giving a final mass of 2.35 grams pure CaCO3 (100.087 g/mol). Calculate the % Calcium (40.078 g/mol) in the sample.

Consider the series of reactions to synthesize the alum (KAl(SO4 )2 · xH2O(s)) from the introduction. (a) Assuming an excess of the other reagents, from one mole of aluminum Al (s), how many moles of alum will be produced?  (b) Assuming an excess of the other reagents, from one mole of potassium hydroxide KOH, how many moles of alum will be produced? (c) Assuming an excess of the other reagents, from one mole of sulfuric acid H2SO4 , how many moles of alum will be produced? (d) If you start the synthesis with 1.00 g of Al, 40.0 mL of 1.50 M KOH, and 20.0 mL of 9.00 M H2SO4 , which of the three will be the limiting reagent? (e) Assuming that the product is anhydrous (that there are no waters of hydration), calculate the theoretical yield of alum, in grams, based on the amounts of reagents in part (d). 3. Consider the nickel salt: (NH4 )2Ni(SO4 )2 ·y H2O (Ammonium Nickel Sulfate Hydrate), where y is the number of coordinated waters. (a) Assuming that the product is anhydrous (y = 0),…

Define: (a) ore; (b) mineral; (c) gangue; (d) brine.

A 1.1324 g sample of magnetite ore was dissolved in concentrated HCl to give a solution that contained a mixture of Fe2+ and Fe3+. Nitric acid was added and the solution was boiled for a few minutes, which converted all of the iron to Fe3+. The Fe3+ was then precipitated as Fe2O3*xH2O by addition of NH3. After filtration and washing, the residue was ignited at a high temp to give 0.5394 g of pure Fe2O3. What is the percent Fe and the percent Fe3O4 in the sample?