I need only output code (py) very quickly needed ObjectiveWhat is the output for the below code?alass InvalidPassengerExoeption (Exception) :passalass Booking:definit_ (self,passenger_list):self.passenger_list-passenger_list101112def validate passenger (self,passenger_id) :flag=Falsetry:for check_passenger in self.passenger list:if check passenger== passenger id:1314151617181920flag=Trueif flag==False:raise InvalidPassengerExceptionprint ("Invalid passenger")except InvalidPassengerException:print ("Passenger exception within class")booking list1=Booking ([101,106,107,110])try:booking listl.validate passenger (L03)except Exception:print ("Something is wrong")except InvalidPassengerException:print ("Passenger exception outside glass")finally:print ("Done")You're being proc

Python is a very famous programming language these days, It is an Object oriented programming, which…

Answered: I need only output code (py) very…

Engineering

Computer Science

I need only output code (py) very quickly needed

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Your task is to write code to implement a two-tone siren using the QUTy. You must use one of the Waveform Outputs of TCA0 to drive the buzzer. The buzzer should always be driven with a 50% duty cycle signal. Your siren must alternate between the following frequencies: f1 = 2110 Hz with f1 active for t1 = 370 ms f2 = 4960 Hz with f2 active for t2 = 630 ms main() will call the init() function you write below and then drop into an infinite loop. The init() function you write MUST return to demonstrate your code is interrupt driven. In addition to init(), you may write any code you wish in this file, including ISRs. // NOTe: make sure to use the buffered versions of the CMP/PER registers //! NOTE: DO not use _delay_ms or _delay_us, we want you to do the math //! yourself and make your program interrupt driven
8 In the following code, use the dropdowns select the correct values of the register al at different points during the program. (Note: ignore the extra spaces inside of the brackets, they have to be there for the dropdowns to work correctly) .databyteArray BYTE 1, 2, 3, 4, 5, 6.codemov esi, OFFSET byteArrayadd esi, 3mov al, [esi ] ; al = ????Answer??????sub esi, 2mov al, [esi ] ; al = ???Answer??????? 9
Use the following data declarations: .data byte Val word Val sbyte 1, 2, 3, FCh word 1000h, 2000h, 3000h, 4000h dwordVal dword 34567890h, 90785634h, 0Ah, 33445566h Show the value of the final destination operand after each of the following code fragments has executed: (If any instruction/s is invalid, indicate "INV" as the answer and briefly explain why) a. mov bh,byteVal+2 b. mov edx,1 C. add dx,[wordVal+4] mov ecx,5 xchg ecx,[dwordVal+12] d. mov ah, byte Val+3 sub ah,[ byte Val+0] sub ah,[ byte Val +2] e. mov eax, dword ptr dwordVal+7 f. movsx cx,byteVal+3 answer bh= answer edx= answer ecx= answer ah= answer eax= answer (show your answer in binary) CX=
Below you can see a Mealy and Moore design code as well as simulation (test bench) code. Can you write note on side of code illustrating what the line represents and explain how the two codes are behaving differently? Mealy: Design source code: module mealy #Example of where the notes should go to represent how the lines are behaving ( input shift_start, input shift_stop, input rst, input clk, input d, output reg [7:0] q ); parameter Idle =2'd0; parameter Start =2'd1; parameter Run =2'd2; parameter Stop =2'd3; reg [1:0] state; reg [4:0] delay_cnt; always @(posedge clk or negedge rst) begin if(!rst) begin state <= Idle; delay_cnt <= 0; q <= 0; end else case(state) Idle : begin if(shift_start) state <= Start; end Start : begin if(delay_cnt ==5'd99) begin delay_cnt <= 0; state…
Q2. [Structural Verilog] Design a 2-bit subtractor unit. Inputs are A and B, and output is S, 2-bits each. As a sub-module you can call the Full Adder module (E Assume this is given to you as library) which takes in 3 inputs (X, Y and Z) and produces 2 outputs (F, C). Write structural HDL
Use MIPS assembly to write the code for a function that computes a factorial of a number that is passed as and argument
Need only flow chart and code in handwritten. Please do fast I didn't have much time
I get an error in LC3 assembly programming when i try to run this code. can someone explain how i can fix this and give me the solution to the fix. i will be very thankfull
what is the correct code for this problem?
An interesting application of a PLA is conversion from the old, obsolete punched cards character codes to ASCII codes. The standard punched cards that were so pop- ular with computers in the past had 12 rows and 80 columns where holes could be punched. Each column corresponded to one character. so each character had a 12-bit code. However, only 96 characters were actually used. Consider an application that reads punched cards and converts the character codes to ASCII. a. Describe a PLA implementation of this application. b. Can this problem be solved with a ROM? Explain.
You must complete this in Python and the programs should not take any command-line arguments. You also need to make sure your programs will compile and run in at least a Linux environment. In this problem, you need to implement operation bit encoding for Assembly instructions. Given a line of text, your program should check whether it is a valid Assembly instruction type. If it is, your program should print out the opcode and optype of that instruction type; if the line of text is not exactly a valid Assembly instruction, your program should skip it and move to the next line of input without printing anything. Input Format The input to the program will consist of some number of lines. Each line contains some text, either a valid Assembly instruction type (with no extra whitespace or other characters, e.g. READ on a line by itself) or some other text. Constraints There are no specific constraints on the length or number of lines. They will be in a reasonable limit, as demonstrated by…
Please use python code Integrate y'=siny y(0)=1 from x=0 to 0.5 with Euler's method using h=0.1.