I need a solution within 15 minute

Q: Q3/The device shown is a part of an automobile seatback release mechanism. The partis subjected to…

A: Given data: F1=4 NF2=2 NMA=300 N.m Need to determine the equivalent force-couple at point O.

Q: Find the centroid of the shaded area in the attached file K3cm Зст 1cm 3cm 1cm

A: To find out the centroid of this figure from x-axes and y-axes. First, find out all section…

Q: Design a helical compression spring to be used in a cam and follower mechanism made of oil tempered…

A:

Q: Q2/Calculate the moment of the 250-N force on the handle of the monkey wrench about the center of…

A:

Q: Q1/ Draw Sectional Front view (Front section), Sectional Side view (Side section),and Draw the…

A:

Q: as shown in figure shown below if the velocity of water at point (A)is(30m/s)with pressure of (90000…

A: We have to find pressure and speed of water at point a, b and c

Q: Q4 If the vertical component of the force F applied to the ring is (10 Ib), determine the magnitude…

A:

Q: Q5 / The 20-kg sliding panel is suspended from frictionless rollers that run on the horizontal rail.…

A:

Q: The chandelier is supported by four chains which are concurrent at point O. If the force in each…

A: Let us redraw the above diagram along with the tension in the rope and the angle the rope makes:…

Q: The coefficients of friction are , 0.4 and a-0.3 20 kg between all surfaces of contact. Determine…

A:

Q: 03/ Find the effective time constant for G(S) Y(s) 16 G(s) X(s) 1.5s2 + 2.4s +6

A: Given, Transfer functionG(s)= 16/(1.5s^2+2.4s+6) Required: Effective time constant.

Q: WHAT ARE THE DIFFERENCE BETWEEN THE TURBO ROCKET ENGINE AND TURBO RAMJET ENGINE in airplane

A: The ramjet engine are different from turbojet rocket engine. The RAMJET ENGINE can not operate at…

Q: Q2. A gas turbine with air as the working fluid has two ideal turbine sections, the first of which…

A: As per given Question  Compressor input temp. =290K Compressor input pressure =100KPA Compressor…

Q: Q1) the torque on the crankshaft of engine is given by : T(N.m) = 25320 + 12600sin20 – 15650cos20…

A:

Q: Q1-in all figers. as shown. F=700 COS (60t) Newton . find the equation of motion , amplitude of the…

A: For solution refer below images.

Q: Q-2 Figure below shows a shaft that is loaded as given, essentially in bending. Bearings are located…

A: Given data Diameter of the shat at B = D = 45mm Dimeter of the shaft at C = 55mm Shaft is loaded at…

Q: H.W.: Draw the I. L. for the axial force in member BE for the truss shown below. F G H 3 m D 304 m…

A: h

Q: The rod OA rotates counterclockwise with a constant angular velocity of @-5 rad/s. Two pin-connectod…

A:

Q: Determine the range of weight (W) that the block shown in figure (3) may have, whi make it neither…

A:

Q: A solid circular bar is welded to a structural member, as shown by a fillet weld all around the bar.…

A: I am thinking that the value of permissible shear stress is 70 N/mm2 in place of 70 kN /mm2 , but i…

Q: Find the moment of inertia with respect to X and Y axes Y Зст 1cm Зст 1cm 7cm

A: Moment of inertia of an area is defined as the product of area and the distances of its center from…

Q: Q1: Steam at 2 Mpa and 250 C is expanded isentropically to 0.36 Mpa and it is then further expanded…

A:

Q: 28 Collars A and B slide along the fixed right-angle rods and are connected by a cord of length L.…

A:

Q: The slider B on the link shown below moves to the lift with a constant velocity of (2 m/sec).…

A:

Q: Q1// Determine the scalar components R, and Ry of the force R along the nonrectangular axes a and b.…

A:

Q: Under the action of force P, the constant accelera- tion of block B is 3 m/s to the right. At the…

A: Given:- VB=2m/s aB=3m/s2 To find:- VB/A=? aB/A=? Vc=?

Q: Two masses m 3.2 kg and my 8.9 kg a massless pulley of radius R 131 cm. r k 12 N/m and equilibrium…

A:

Q: Q1: The gases in the cylinder of an internal combustion engine have a specific internal energy of…

A: Step by step solution is given below

Q: An air engine Works on theideal eycle in which heat is received and Yejected at Constant volume. the…

A:

Q: A lead object is dropped from a height of 10 m onto a hard floor. The object bounces, rising to a…

A:

Q: 3. Obtain a state-space representation of the mechanical system shown below, where u₁ and u₂ are the…

A:

Q: Aluminum bar with 100mm diameter and 500mm long is turned down to 88mm diameter, using two passes on…

A:

Q: Q4: A hot surface at 100°C is to be cooled by attaching 16 number, 3-cm-long, 0.25-cm- diameter…

A: for each fin we have to consider the analysis of each fin then evaluate the overall surface…

Q: 8. For a wave with a wavelength of 4 m trying to move through an opening with a width of 4 mm: would…

A: The answer is provided below.

Q: Homework 9- Determine the total energy production of a run-of-river plant having an total efficiency…

A: Given:

Q: Knowing that u=0.30, determine the acceleration of each block when m-1mg, m=2mc

A: According to Newton's second law of motion, the net force acting on any object is equal to the…

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.