i) Justify the reason that normalizing heat treatment process is less expensive compared to annealing. ii) Differentiate hardening heat treatment process and tempering heat treatment process.

Q: A torsion dynamometer is fitted on turbine shaft to measure the angle of twist. The shaft twist 1.6°…

A: A torsion dynamometer is installed on the turbine shaft to measure the angle of twist, as we know.At…

Q: 15 m/h water enters the turbine at 20°C and leaves it at 50°C. The internal diameter of the inlet…

A:

Q: 1-8 Discussions Discuss or explain each of the followings: 1. Effect of the carbon percentage on the…

A: Note :- you have posted multiple questions on single window. As per the guidelines I am able to…

Q: Figure Q4 (b) displays the time-temperature cooling paths for a 1080 steel on an isothermal…

A: In the given diagram, it can be seen that for paths (i) and (ii), the final position lies below the…

Q: The following data are obtained from a tensile test of a copper specimen. - The load at the yield…

A: Note: As per our guidelines we are supposed to answer only the first 3 sub-parts. Kindly repost…

Q: A shaft rotating at 120 r.p.m is supported in bearing A and B, 1.8 m apart, A being at the left-…

A: Note: Since you have posted a question with multiple subparts, we will solve the first subpart for…

Q: Section 2: Numerical Response Q3 : If the flow into a wind turbine is 10 m/s, and the flow far…

A: Given:The upstream velocity of flow, The downstream velocity of flow,

Q: 1. In a turning operation, the diameter of the work- piece is 2 inches (50 mm), and it rotates at…

A:

Q: an advertising panel erected on uneven ground is supported by the EF and EG guy lines. If the force…

A:

Q: Perform detailed analysis (Draw the cycle schematic and T-s diagram; find the turbine output work,…

A:

Q: Metric thread of 0.8 mm pitch is to be cut on a lathe. Pitch of the lead screw is 1.5 mm. If the…

A: The speed of rotation of the lead screw is 800 rpm.

Q: Define the following phrase; i. External forces ii. 111. iv. V. Forces generated by motion Forces…

A:

Q: A system is at steady-state if none of the system properties changes with losing heat none of the…

A: .......................... A system is at steady-state if Answer: none of the system properties…

Q: Base radius ro Oil 20 A solid cone of angle 104.8 degrees, base 15.2 cm, and density 2745 kg/m3 is…

A:

Q: Which of the following is the best example of engineering control? A. noise-cancelling headphones

A:

Q: Cold working is the good way to shape brittle material Select one: O True O False

A: Cold working  is a  metal working process in which metal is reshaped below its recrystallization…

Q: Aparticle Moves with the equation alt=sinzt where alt): Acceleration in m/s" and, t., are the time…

A:

Q: (a) Determine the pressure difference between pipes A and B shown in Figure Q2 (a) when a, b and c…

A:

Q: Q3/A multi – plate clutch is to transmit 12 kW at 1500 r.p.m. The inner and outer radii for the…

A: We are suppose to solve only 3 subparts. Please post other parts as a separate question.

Q: Q3. Nitrogen gas undergoes the cycle shown in the figure below. What is the volume at State 3 and…

A: Given data: Image with relevant details as shown above   To determine: Wnet for the cycle…

Q: If the available power supplied by the engine of a vehicle weighing 10 kN is 30 hp and is designed…

A:

Q: Q2 (a) A motorcycle travels east 2 km for 5 minutes, then north 3 km for 8 minutes, and then west 6…

A:

Q: Chicken cannons are designed to fire dead (frozen) chickens in order to test aircraft engines and…

A: A chicken gun is nothing but a compressed-air cannon used to rocket dead birds into aircraft engines…

Q: 1. During a ground test with both main and tail rotors in steady operation, a 400 N aerodynamic…

A: Given   Force, F = 400 N Distance, d = 6 m Find  Force couple system, C

Q: 2. Given: The piston rod of the hydraulic cylinder C imparts a constant acceleration to pin A of as…

A:

Q: 2. A machine shaft turning at 600 rpm is supported on bearings 20" apart. Twenty HP is supplied to…

A: Given: The shaft speed, N = 600 rpm The distance between bearing, x = 20 in The diameter of pulley,…

Q: 4. Determine the horizontal force exerted on block E. F = 150 16 6 in BD 11 8 in a B 150 6 in. D E

A:

Q: 2-25. As the balloon ascends, measurements indicate that the temperature begins to decrease at a…

A:

Q: Please answer the question

A: Given Data Length of the rod is: L=4 m Mass of the rod is: mr=40.775 kg Mass of the thin disc is:…

Q: (a) The crankshaft AB shown in Figure 1.1 is rotating clockwise with an angular velocity of wAB = 6…

A:

Q: Q3/A multi – plate clutch is to transmit 12 kW at 1500 r.p.m. The inner and outer radii for the…

A: Step by step solution is given below.

Q: If the load P= 60N on the beam causes the end C to be displaced 10 mm downward: a) determine the…

A: Given-Data:- P=60N Assuming the length BD=4m To-Find:- a) Normal Strain in BD b) Shear Stress in…

Q: A multi-fluid manometer shown in Figure 1 is used to measure the pressure in a water tank…

A:

Q: 4. Develop the K for the relationship T = Kcp ŋ SN for the cone-and- plate rheometer; plate of…

A: Viscous force equation, F=AηVyF=Viscous force,A=Area of the moving plate,η=coefficient of…

Q: Estimate the flow rate Q at time t = 4s by using: (a) 2-Point Forward Difference (b) 2-Point…

A: Q = dVdt (a) Forward difference: f'(x) = f(x+h) - f(x)h (b) Backward difference: f'(x) = f(x) -…

Q: Draw the free body diagram (F.B.D) of the 100-Kg system that consists of pin connection at A and…

A: Free Body Diagram

Q: 7. In sand casting, the volumetric size of the pattern is (a) bigger than, (b) same size as, or (c)…

A: Answer:  Bigger than cast part. Because during the process of casting  the metal may tend to shrink.…

Q: A body having a cylindrical shape of length equals to 1.9 m and diameter equals to 400 mm is inside…

A: Lumped Capacitance method is a method of heat transfer analysis, where a spatially uniform solid…