I Example 7-1 In a step-up converter, the duty ratio is adjusted to regulate the output voltage , at 48 V. The input voltage varies in a wide range from 12 to 36 V The maximum power output is 120 W. For stability reasons, it is required that the converter always operate in a discontinuous-current-conduction mode. The switching frequency is 50 kHz. Assuming ideal components and C as very large, calculate the maximum value of L that can be used.

I Example 7-1 In a step-up converter, the duty ratio is adjusted to regulate the output voltage , at 48 V. The input voltage varies in a wide range from 12 to 36 V The maximum power output is 120 W. For stability reasons, it is required that the converter always operate in a discontinuous-current-conduction mode. The switching frequency is 50 kHz. Assuming ideal components and C as very large, calculate the maximum value of L that can be used.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Input voltage of a boost converter 80 V, output voltage 140 V and switchingits frequency is 20 kHz. The converter efficiency is known to be 95%.a) Continuous conduction (current) in operation when the load resistance changes between 14 - 20ohmThe lowest inductance (L) value and output that should be used to maintain the operation.the peak-to-peak value of the voltage ripple should be used to be 2% of the output voltage.Calculate the capacitor's capacity (C).
An RL load (R=0.2 Ohms, L=10 mH) is controlled by a converter. The supply voltage Vs is 600V and the chopper frequency is 200 Hz. The maximum peak to peak ripple current is equal to: Select one: a. 30A b. 55A c. 90A d. 75A
An ideal boost converter is required to have a constant output voltage of 12 V at 24 W load.The input voltage varies from 2.7 to 4.5 V (as in a battery cell). Select a switching frequency of100 kHz. The value of the inductance in the boost converter is 2.2 uH. Determine:(a) The range of duty cycle that the converter will operate with (hint: mode?), and(b) The minimum value of the output capacitance such that the pk-to-pk load voltage rippleis less than 2%.
9- Buck type DC-DC converter, if the input voltage is 789 V and the occupancy-backlash ratio is 0.9, which of the following options is the correct load voltage. a) 710.1 etc) None c) O 7101 V d) O 78.9 V
You are an electrician working on an overhead crane. The crane uses a large electromagnet to pick up large metal pipes. The magnet must have a minimum of 200 VDC to operate properly. The crane has an AC source of 240 V. You are given four diodes that have a peak voltage rating of 400 V each. These diodes are to be used to form a bridge rectifier to convert the AC voltage into DC voltage. Is the voltage rating of the diodes sufficient? To the nearest volt, what will be the DC output voltage of the bridge rectifier?
b) A Buck-Boost converter has an output of 24 V from a 5 V input with diode ripple current of 2.4 A and switching frequency of 100 kHz. Find the duty cycle and the inductance of the converter.
In ............ mode of operation, fully controlled converter will keep a delay angle range between 90 to 180.
Dc converter
18. A dc-dc converter is to be built with the following specifications: Allowed dc input voltage range: +8 V to +18 V +24 V Output average voltage: Output voltage ripple: ±0.06 V maximum at rated load 300 W, resistive ±250 mA maximum at rated load 100 kHz Rated load: Input current ripple: Switching frequency: Common ground between input and output. a. Draw a circuit which can perform this function. b. What is the necessary range of duty ratio for each switch? c. Find circuit part values (R, L, and C) which will meet the stated specifications.
Sub:power electric
Find the delay angle of 1 phase half wave converter has 120V supply rms voltage with the value of the resistor is 10Ohm. The average output voltage is 25% of the maximum possible output voltage then find the delay angle.
Assume AT the output of a filtered half wave rectifier circuit a series resistor RS of 4.2kohm together with a shunt connected 54v zener diode is now connected as a simple regulated circuit. The zener is connected in parallel with load RL of 11.9 kohm. When the input mains voltage flutes at various parts of day the max DC voltage appearing across the capacitor is 120 V and thefor the above zener maximum voltage is 80 V. Determine the load current in mA flowing through the load,