(i) Determine the acceleration of the system. (ii) Draw the free body diagram and kinetic diagram for both the truck and trailer. (iii) Based on the diagrams in (ii), determine the horizontal force developed in the coupling, C, and the frictional force developed between the tires of the truck and the road during this time.

(i) Determine the acceleration of the system. (ii) Draw the free body diagram and kinetic diagram for both the truck and trailer. (iii) Based on the diagrams in (ii), determine the horizontal force developed in the coupling, C, and the frictional force developed between the tires of the truck and the road during this time.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

b) Figure Q1 below shows two blocks, A, and B each with mass 60 kg and 150 kg respectively. The blocks are connected by pulleys. If block B is moving down the 60° indline plane with coefficient of kinetic friction of u. = 0.15 and the mass of the pulley and cords are negligible, i) Draw the free body diagram and kinetic diagram for block A, B and pulley D ii) Write down the equation for acceleration of block A in terms of block B. A 60 Figure Q1
A 5-kg block is acted on a 30-N tensile force that acts 50° from the horizontal. The kinetic coefficient of friction is 0.25. What is the acceleration of the block?
1. Two identical beads A and B each of mass m connected by a light rod of length rv2 can slide without friction on a fixed ring of radius r. The beads are also connected to fixed points C and D with identical elastic cords each of force constant k and relaxed length rv2 as shown in the figure. Initially the cords coincide with diameters of the ring and the system is in equilibrium. Now the bead-rod assembly is displaced slightly aside and released. Find acceleration of the point of intersection Pof the cords immediately before a cord becomes relaxed. B D Ans = I need to know how this answer mv2 Comes show every step of solution P.
5. Three blocks are connected over two frictionless, massless pulleys by two inextensible, massless cords as shown in the figure. There is friction between block m and the horizontal surface of the table. If the block m, moves downward after being released from rest, then what is the magnitude of the acceleration of the blocks and the magnitude of the tension in the cords in terms of the masses of the blocks m, , and ms, the coefficient of kinetic friction between block my and the table, a. and the acceleration due to gravity, g. Include a force diagram or free-body diagram of the situation.
A helical spring has a stiffness of of 25 kN/m. If a mass of 100 kg is attached to its free end, pulled down, and then released, (a) amount of deflection, in cm, (b) determine the periodic time of its motion. (c) If the maximum deflection was 50 mm, find the velocity and acceleration of the mass when it is 300 mm from the equilibrium position. Make an illustration.
Please show me the steps for a,b,c,d
Figure Q2 shows a spool with a mass of 20 kg and a radius of gyration ko = 0.16 m. The 15 kg block A is released from rest position. Apply the conservation of energy method to determine the distance that block A must fall for the spool to rotate at an angular velocity of 8 rad/s. (a) Apply the principle of work and energy to determine the tension in the cord when the block is in motion. (b) (b) What are the assumptions made in the analysis? 0.2 m A Figure Q2
A platform in the form of a solid disk with a radius of 1.5 m and a mass of 180 kg rotates by inertia about a vertical axis with a frequency 10 revolutions per minute. A person of 50 kg mass is standing in the center of the platform. (a) What linear speed relative to the floor will a person have if he goes to the edge of the platform? (b) How much has the kinetic energy of the system changed and due to what?
Question 4 a) State the assumptions made in the definition of the rigid body and explain different possible types of motion of a rigid body. b) The 10-kg block A rests on the 50-kg plate B in the position shown in Figure Q4(b). Neglecting the mass of the rope and pulley, and using the coefficients of kinetic friction indicated, determine the tension in the cable, acceleration of block A, plate B, and the time needed for block A to slide 0.5 m on the plate when the system is released from rest. AB=0.2 0.5 m A B 30° + PBC = 0.1 Figure Q4(b)
Two blocks A and B with masses mA = 10 kg and mB = 4 kg are connected by an inextensible cable and released from rest shown in Figure 1 (where block A is placed in position C). The cocfficients of kinetic friction between two blocks and the 30° inclined plane are uA = 0.1 and MB = 0.3. The cable is in tension in the entire motion and the sizes of blocks are negligible. (Take gravitational acceleration as 10 m/s2) - Draw separate free body diagrams of blocks A and B. Indicate clearly all the forces, directions of motion and coordinate systems. Based on the free body diagrams in part (a), cstablish the cquations of motion for blocks A and B and determine the tension in the cable between two blocks. Detemine the time required for block A to move 2.5 m from positions C to D along the incline and the velocity of block A when it reaches position D. B 2.5 m A-03 0-30° Figure I
5. A 9kg rod with L-0.4m is free to rotate without friction about Point A. It is released from rest at the vertical (upward) orientation shown (State 1). What is the speed of the free end of the rod, Vaz, when the rod has rotated 180° (State 2)? State 1 State 2 4 L=0.4 m A ay=0 m=9 kg V82= ? B
Problem Consider the inverted pendulum shown below that consists of a massless rod of length L and a pendulum bob, P, of mass m. The pendulum is initially at rest in position A when it is struck by a hammer. The average force magnitude applied by the hammer to the bob is F in the horizontal direction. The impulsive force is only applied for a very short time of T seconds. 6 Part A: (Angular Momentum) Determine the angular momentum vector, hp/o, of the bob im- mediately after it is struck in terms of one or more of the following variables: (m, L, F, T,g). Part B: (Conservation of Energy) A short while later, the pendulum bob reaches a maximum height of h and is in position B. It has zero velocity at this instant. Determine h in terms of one or more of the following variables: (m, L, F, T,g). [Hint: determine the speed of the bob after impact from your answer in Part A.] O L Ө Fm P Position A Position B h g