Q- 2 An AC circuit is given in Fig.2. Please:i)Consider that C, and L1 are connected in series and find the equivalentimpedance Zi of the circuit branch containing C1 and Li;ii)equivalent resistance of both branches that are connected in parallel;Consider that both Rị and R2 are connected in parallel and find theiii)Use the result from i) and ii), consider that Zi is connected in series tothe group containing the resistors R1 and R2 and find the equivalent impedance in theinput of the circuit;Use the result from ii) and find the instantaneous value of the inputcurrent im(t) = ?, if R1 = 22, C1 = 0.01F, L1 = 0.01H, R2 = 2, vin(t) = 4 sin(@t) volts,iv)and o = 100 rad/S.CiLiim(t)Vin(t)R1R2Fig.2indui

i) Consider that C, and L, are connected in series and find the equivalent impedance Zi of the circuit branch containing C1 and L1; ii) Consider that both Rị and R2 are connected in parallel and find the equivalent resistance of both branches that are connected in parallel; ii) the group containing the resistors R1 and R2 and find the equivalent impedance in the input of the circuit; Use the result from i) and ii), consider that Zi is connected in series to iv) Use the result from iii) and find the instantaneous value of the input current im(1) = ?, if R1 = 20, C1 = 0.01F, Li = 0.01H, R2 = 292, vin0) = 4 sin(t) volts, and w = 100 rad/S. HE Ci Li Vin(1) RI R2 Fig.2 Induį

i) Consider that C, and L, are connected in series and find the equivalent impedance Zi of the circuit branch containing C1 and L1; ii) Consider that both Rị and R2 are connected in parallel and find the equivalent resistance of both branches that are connected in parallel; ii) the group containing the resistors R1 and R2 and find the equivalent impedance in the input of the circuit; Use the result from i) and ii), consider that Zi is connected in series to iv) Use the result from iii) and find the instantaneous value of the input current im(1) = ?, if R1 = 20, C1 = 0.01F, Li = 0.01H, R2 = 292, vin0) = 4 sin(t) volts, and w = 100 rad/S. HE Ci Li Vin(1) RI R2 Fig.2 Induį

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Get two equations whose unknowns are the voltages of the first and second nodes (e1 and e2) using Kirchoff current laws, Kirchoff voltage laws, and element definition relations? (Select nodes e1 and e2 as desired. Select the direction of the currents I1, I2, and I3 as you wish. "3-uçlu direnç" means 3-pin resistor.)
This Homework is too much... i already solved 3 question but still alot to go.. Please Help me Solve this.
For the given circuit in Figure below, find the open circuit voltage VTH and the short circuit current IN across the terminal. then, find R TH by using the RTH=VTH/IN equation and find RTH with replacing voltage source with short circuit. Let’s assume we connect RL (load resistance) to the circuit between points A and B, what should be the value of RL in order to have max power transfer.
PROBLEM 3: Consider the circuit shown below in which you are to assume that Vsi, Vs2, Is and the resistors are known. Use the node voltage method to compose the minimum set of equations sufficient to determine all of the labeled node voltages (i.e. A through F). Do not include redundant equations! Your equations should be in terms of ONLY the node voltages, Vsi, Vs2, Is, and the resistors. You do not need to arrange the equations in matrix form nor to simplify them algebraically. Vs₁ F + R₁ VD E R₂ www R4 A B + R3 C VS2 R5 Is
Help me please
its not graded as before rejected
I posted the same question but the value are wrong .. please check.. Ans for v2 and v3 should be 1.2500V & -1.2500V.. 1. Construct the circuit as shown in Figure 1. Set VS1 and VS2 to 5 V. Measure each of node voltages and record that results in Table below.R1= 1kR2= 3.3k R3= 2.2kR4= 4.7kR5= 1.2k Table 4.2: Nodal Voltage Values Parameter (Volts) THEORITICAL V1 V2 V3 V4 Please draw the current flow in arrow in the circuit. Tq
For the circuit shown, select the values of R1, R2 & R3 so that: y11=0.006 mho, y12 =y21=-0.001 mho & y22=0.003 mho I R2 I2 V1 R1 R3 V2 400 ohm, 500 ohm, and 200 ohm 200 ohm, 400 ohm, and 500 ohm 200 ohm, 1000 ohm, and 500 ohm 400 ohm, 1000 ohm, and 400 ohm
Please see attached screen shot for questions a-f.
Solve the Mesh currents, IR1, IR2 & 1R3 and the voltages across the resistors VR1, VR2, VR3, VR4, VR5 and VR6.Also, please explain the effects of mesh analysis on multiple active linear source
Problem Solving: Simplify and determine the equivalent circuit resistance below: R₁=20 E= 460 V R5= 10000 R₂ = 100 R3 = 100 R4 = 100 www R6=1500 Rg = 600 R7 = 200 R12=200 R8 = 400 R10 = 400 R₁1= 2000 R13 = 2000 R₁4 = 400 R15 = 1000 www R16 = 2000 R17 = 6000 R18 1040 R19 = 104 Hi guys! Here is something you can practice with. Simplify the circuit above. The final answer for this is 153/3 ohms. Good luck!