i-Assume a switch is connected to pin RD7. Make an assembly language program to monitor its status and send two messages to the serial port continuously as follows: SW=0 send "LOW" SW=1 send "HIGH". Assume XTAL = 20MHZ and set baud rate to 9600.

Q: 89. Communication circuits that transmit data in both directions but not at the same time are…

A: Asked: Communication circuits that transmit data in both directions but not at the same time are…

Q: The term that means data is sent over four wires at the same time is a. 4S b. 4D c. 4W d. 4R

A: The term that means data is sent over four wires at the same time is 4D.

Q: Processors are designed to promptly stop whatever they are doing when they get a signal and respond…

A: Extended-release Security Context controls access points programmatically. Several boats use…

Q: PIT clock i

A: Given : - A programmable interval clock (pit) clock is given and operating frequency is,  f =  24MHz…

Q: When a word of data is Input from the I/O address AAAAH, the state of the control signal which occur…

A: ANSWER: BHE#0, A0=0, M/IO#=1, DT/R#=0, RD#=0, WR#=1, DEN#=0 Explanation Transport High Enable &…

Q: Computer science Describe the SSB synchronisation issue.

A: Introduction: PSS, SSS, and the physical broadcast channel make up the Synchronization signal block…

Q: Given the situation described below, which of the following signal states are correct? [select all…

A: The 8284 that includes the clock generator like that is capable of third of the frequency of the…

Q: Write an embedded C program to transmit 7-bit data with two stop bits and even parity at 9600 Baud…

A: first of all what is ATmega32 in c program? This introduction to embedded programming intends to…

Q: Define the classic synchronization error known as a race ?

A: Answer for the given question : A race condition is a blunder in synchronization brought about by…

Q: Assume that port 0 is connected to the input and port 1 to the output (LED). Number times LEDs on…

A: One must take hardware's or microcontroller's clock speed into account when calculating the…

Q: Can you tell the difference between parallel and serial transmission?

A: Our task: Differentiate between parallel and serial transmission?

Q: I have six ESP-WROOM-32D boards and six NRF24L01 modules. Each ESP-WROOM-32D board is connected to…

A: In a world increasingly reliant on seamless data exchange, the ability to establish robust…

Q: Write the values of EICRA to configure the ATMEGA1280 for pins 3 and 1 to interrupt on the falling…

A: EICRA( external interrupt control register A)   ISC31 ISC30 ISC21 ISC20 ISC11 ISC10 ISC01 ISC00

Q: 3. A switch is connected to the bit 3 of PORT A. Monitor it to check if it is ON. If the switch is…

A: Answer is given below-

Q: What more input and output signals does the danger sensing unit shown in Figure 4.60 need if no…

A: Introduction: Pathogen-associated molecular patterns (PAMPs), danger signals (Matzner, 1994), safe…

Q: Assembly language program a wave on the port pin P1.0

A: Below the assembly language program a wave on the port pin P1.0

Q: what is the maximum delay that can be generated using 16-bit timer0 with 1:8 prescaling?

A:

Q: Write a program to get data from port B and send it to port C continuously while an interrupt will…

A: Requirements:Continuously read data from Port B and send it to Port C.Use an interrupt such that a…

Q: QUESTION 31 The address field of a frame relay frame will always end with a binary 1. O True False

A: address field of frame relay will always end with binary one.

Q: If you want to configure your AVR AtMEGA 328 for serial communication to asynchronously send and…

A: Solution:--   1)The given question has required for the solution to be provided with the help of the…

Q: The most widely used application/programming interface for UPD is the:?-layer-socket-tellnet-adu

A: The most widely used application/programming interface for UPD is the:?-layer-socket-tellnet-adu

Q: An existing GPIO library is to be expanded by a function with which Set / delete / toggle any…

A: Answer: I have given answered in the handwritten format in brief explanation.

Q: Seven segment LED display (common cathode) is connected to port 2 of 8051 as shown in figure below.…

A: ANSWER: Seven Segment Display: A seven-segment display is a combination of eight LEDs connected in…

Q: Compute the time delay generated by an Atmega32 (XTAL = 8MH2) that is programmed by the following…

A: Solution!!

Q: Q1. Two switches are connected at P1.0 and P1.1 respectively. Four LEDs are connected at P2.0, P2.1,…

A: The 8051 has two timers/counters. They can be used  as timers to create time delays . Alternatively,…

Q: The Arduino Uno has a 10-bit ADC. What is the value of val’ in the following cases? ) val =…

A: As per our company guidelines we are supposed to answer ?️only first 3️⃣ sub-parts. Kindly repost…

Q: Write a program for the MSP-430 FR 6989 Eval board with the attached IR-board that broadcasts a…

A: This program can be defined in such a way that it will first configure the IR LED pin as an output…

Q: 18. What is the function of IO/M signal in the 8085?

A:

Q: Which choice is a feature of the SPI bus? O A formal specification with fixed bit rates O It uses…

A: The correct option is

Q: how do we know that the serial port has received a certain number of bit data byte in a program?

A: The question is how do we know that the serial port has received a certain number of bit data byte…

Q: Difference between RS 422 and RS 423 serial interfacing standards

A: Solution:-

Q: Write MIPS code to echo one keyboard input to the monitor, where your code shall do the following:…

A: the program is given below:-

Q: This 8-bit word 10011010 is fed as control/command word to following devices: 8255, 8254, 8237, and…

A: All the mentioned devices accept the 8 bit word as either command or control. Each bit of the word…

Q: the following protocol used to Synchronous serial interface Select one or more: a. interface…

A: Synchronous Serial Interface (SSI) Protocol used for  Answer: c. secure digital card

Q: A microcontroller is used to interface an AC load through a relay. L1 20V U1 RAOC12NO-AND RAIC1NJANT…

A: Actually, given question regarding Microcontroller.

Q: Suppose we want to generate a PWM signal to toggle an LED every one milliseconds (1ms), which…

A: In the intricate world of microcontroller programming, generating Pulse Width Modulation (PWM)…

Q: Choose... 1.default mode The real mode of operation is 2.is a control bus the protected mode of…

A: The solution to the given problem is below.

Q: What is the switching speed? a) 60 times per second b) 50 times per second c) 55 times per second…

A: Question. What is the switching speed? a) 60 times per second b) 50 times per second c) 55 times per…