Hydraulic. Please solve with explanation.

Q: Part of the screw thread connecting the adjacent flank on top of the screw thread is known as O…

A: Correct answer is option (b) Pitch  The pitch of a thread is the distance measured parallel to its…

Q: Forces of magnitude F; =7 kN in the +y direction and F 2 =13 kN in Question 2) the -z direction are…

A:

Q: : the components of the 100 lb force are B. l00 A 60 30

A: Given data: Magnitude of the force = 100 lb Need to determine the components of the force along A…

Q: 8. The linear impulse (1) of the force F- (30) N for t-4 seconds is: a. 40 N.m b. 20 N.m c. 16 N.m…

A: Given data: The time is, t=4 s. Write the given expression. F=3t

Q: Nut 17.0 N 37° 25.0 cm

A: The text provides the following information:The force applied to the wrench is 17.0 NThe distance…

Q: dr. リ+ y + tan²t – 1 dt dy dt =-+tant 山一位

A:

Q: Rotate the objects shown below by the indicated amount. Sketch the result in the space provided.…

A: Find Rotate the object about the given axis.

Q: A n s w e r   t h e  f o l l o w i n g ,   y o u   m a y  f i n d  t h e  a n s w e r s   i n  a n y…

A: Fringe benefits are non-wage compensations given to employees by their employers in addition to…

Q: The traffic light hangs from the cables as shown. Draw a free-body diagram on a coordinate plane for…

A: Given data Weight of light =200N Draw the free body diagram

Q: pered gibs are adjusted by screws spaced out along the length of the gib

A: The statement mentions "Tapered gibs are adjusted by screws spaced out along the length of the gib".

Q: )واجب بتی .H.W F3-5. If the mass of cylinder C is 40 kg, determine the mass of cylinder A in order…

A:

Q: 2KN 3KN रल रल

A:

Q: The weight will always act downwards at an angle of 30 upwards at an angle of 60

A:

Q: Consider the following steel shaft with varying shaft diameter. Determine the rotation of D with…

A:

Q: Write the two equations of equilibrium, EFx = 0 and EFy !3! %3D

A:

Q: D r a w       t h e       i s o m e t r i c      v i e w .   T h e       i m  a g e     i s       i…

A: Given Orthographic view To find Isometric view

Q: The crankshaft of a two-stroke engine spins at about 391 RPM for a brake torque of 983 N-m. If the…

A:

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: Rotate the objects shown below by the indicated amount. Sketch the result in the space provided.…

A: the solution is provided in the picture attached below.

Q: QUESTION 3 Which of the following gives the nearest value for the velocity (in m/s) when the block…

A:

Q: 1. The built-up beam pictured on the right is subjected to an internal moment of M = 75 kNm. a) At…

A: *The internal moment acting on the structure is M=75 kNm. *The total length of the T section is…

Q: P? P G P

A:

Q: В |C O2 4 D 3 A E (201 5 F D 6 H at c I G Needle

A:

Q: Why you put h= 19 instead of h=38 your answer for the exercise is incorrect can you please correct…

A:

Q: 5. (a) (i) A crane hook with a mass of 80 kg exerts a vertical force F downward at A (see Figure…

A:

Q: = The cross-section of a wooden, built-up beam is shown below. The dimensions are L w = 20 mm.…

A:

Q: 4. Use F₁ =3, 6₁ = 2, k₁₂₁ = 4₁ K3 = 2,63 = 1, J₁ = 2₁ J₂=5, find the impulse and step response of…

A: Given: To find: Impulse and step response

Q: Flywheel serves as a reservoir to store and restore energy by virtue of its inertia Select one: O…

A: A flywheel stores the kinetic energy in a rotating mass with a very low loss of friction.

Q: Consider (Figure 1). Figure 0.3 m. 120° 45° 60⁰° 325m Y Part A Determine the magnitude of the…

A: Given data: Force (F)=260 N To find:-the magnitude of the moment of the 260-N force about the x…

Q: write the two equatoins of the equilibrium .Do not solve

A:

Q: y of holding metal in the vice whe

A: Required  correct method for holding metal in the vice

Q: 3-9. Solve for the algebraic sum of the moments in pound-feet about A when h is 20 m as shown in…

A: Given data h = 20m Forces acting are 800N, 500N

Q: QUESTION 2 A single-cylinder, 4-stroke, 3-liter gasoline engine operates at 791 rpm and a…

A:

Q: Figure Q5 (b) shows the tube is made of copper and has an outer diameter of 45 mm and a wall…

A:

Q: 9-30, determine the normal reaction at the smooth support At P-800 N. Neglect the weight of the bar.…

A:

Q: Q 114 Calculate the angle between the two vectors that makes the relationship AB = A correct?

A: Given question: Calculate the angle between the two vectors that makes the relationship A·B = A.

Q: Consider the bar/roller assembly shown in the figure below. The roller and surface at point A are…

A: A free body diagram is defined as a diagrammatic representation of all the forces acting in a…

Q: Part A - Moment due to a force specified by magnitude and endpoints As shown, a member is fixed at…

A:

Q: 13A) coefficient of friction (H) is O a. normal force + limiting friction O b. normal force limiting…

A:

Q: F = 120 lb | 30° 12 kN 1.25"- 30 4 m 1.5" 5 m 11"

A:

Q: O fash O cad shut O dead metal

A: Forging is a manufacturing method that involves shaping metal using concentrated compressive…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.