hown below. The gate is hingeda Friction at the hinge and the weigh P.

Q: Q3) Determine the force in each member of the truss. State if the members are in tension or…

A: A truss is pinned at A and a roller supported at D, to this truss, a 10kN vertical load, and 6kN…

Q: 15KN 25KNM 17 kN B 7m

A: To maintain equilibrium, the sum of vertical force acting on the beam is equal to zero. To…

Q: A frame structure consists of 2” x 2” wood timber and supported by a 10mm dia. cable were build to…

A: We have to determine the maximum normal stresses developed in the structure.  Given data :- weight =…

Q: H.wO A truss Consisting of two members (AB) and (Bc),fird the loacation of JeintB due to the vertial…

A:

Q: The three-member truss is used to support vertical load P. If P-200 kN, find the stress of members…

A: Solution -The given values are as follows, If P =200kNCross sectional Area=6000mm3To Determine The…

Q: Prove if the truss below is determinate, stable, or unstable. P is 3 Kips. Assume A and D as pin…

A:

Q: Determine al! furce of members the truss shown 3 600 4 m

A:

Q: Som

A:

Q: Determine the horizontal reaction in kips at the connection A of the gable frame. Assume that A, B,…

A: Consider the figure,

Q: hat is the approximate axial force in girder EF of the frame shown? Use the port H 30 kN 6 m 10 kN D…

A: The portal method is based on the assumption that, for each storey of the frame, the interior…

Q: 91- 15 15 イ R2 年HE BEAM IS IH EQUILLBRWM. FIND FORCE R1.

A: In this case, the beam is simply a supported beam having a point load, a uniformly distributed load,…

Q: 3. Resolve P = 480-N force into components along the cables AB and AC. Use a=40• and B=25º. %3D B A.

A:

Q: GH

A:

Q: 5-13. Determine the components of the support reac at the fixed support A on the cantilevered beam.…

A: Given that: A cantilever beam as shown in the figure:

Q: The 7/8-in.-diameter pins at A and C that support the structure are in single shear. Find the…

A:

Q: T 2 m 3 kN 2 m LA G -3 m- -1.5 m- (b) *Assume A to be hinged and D to be roller. 6 kN -3m- -3 m- 3…

A:

Q: 30KN 20 KN Im Find the force in member AC. 3m 3m A

A:

Q: ES S 2-34. Determine the horizontal and vertical components of force at the connections A, B, and C.…

A: Determine the horizontal and vertical component of the reaction at A, B and C.

Q: Determine the force in member BE of the loaded truss. 5 kN 45⁰ A B D 1 m 45⁰ 2 kN F 1 m

A:

Q: member of the in figure,'using Compute the force in each Warnen Truss Shown the methed 0f seetions.…

A:

Q: Compute asial forces in all truss members P2: In the previous problem, determine the force in…

A:

Q: Obrain the maxium bending moment ar member B-D of the given frame. A and B are pinned. Assume that…

A: Given, P = 8 kN q = 6 kN/m a = 4 m b = 3 m

Q: T 2 m 3 kN 2 m G LEX -3 m -1.5 m- (b) *Assume A to be hinged and D to be roller. 6 kN F 3 m- -3 m- 3…

A: To Determine :- The support reactions and member forces on the truss.

Q: A horizontal beam AD with cross-section of 3800 mm² is supported by a wire at C and carries a load…

A:

Q: ight acting Id in equilibrium E has been ing and does not Y 2 ft the hinges and B 3 ft 2 ft 10='V D…

A:

Q: please answer as soon as possible

A:

Q: 4- For this truss e=60°, a) Determine the type of supports b) Reaction forces at each support c)…

A: Away from the joint  (+ve) = tensile  Towards the joint (-ve) = compression

Q: 10 kN 10 kN 10 kN 10 kN 10 kN 10 kN 10 kN Q2 (25%): For the simple truss shown, B, A. There are five…

A:

Q: 1-1. The shaft is supported by a smooth thrust bearing at B and a journal bearing at C. Determine…

A:

Q: Replace the loading by an equivalent resultant force and couple moment at point O.

A: The given data is shown below:

Q: 3) Determine the force in member A 10 ft. И И 10 ft. 17 ft. Member A 8 ft.5 ft.-- 10 ft. 1000 lbs.

A: Given:Required :Force in member A

Q: Determine the force for member AB, GF, BC, CK, and BL.

A:

Q: Hinge Roller

A: Using formula to find indeterminacy

Q: Determine the horizontal and vertical components of force at pins A and D. 2m A -1.5 m -1.5 m- 0.3 m…

A: Given data : Structure is given with pulley at E of radius 0.3m Find : Reactions at A and D  Free…

Q: 1-7. Determine the resultant internal loading on the cross section through point D of the pliers.…

A:

Q: lo kJ Determine (approximately) the reactions at the base of the columns of the frame shown. Use the…

A:

Q: Determine the maximum compressive force at member HL due to an 8kN point load.

A: Answer Let us first draw the ILD for member HL Pass a section through member HL as shown below…

Q: What is the approximate axial force in girder EF of the frame shown? Use the portal method. G 80 kN…

A:

Q: 55 KN B 1.5 m 2 m C 2 m E 2.5 m 2m 90 KN G 45 KN F 1.5 m 2 m H

A:

Q: INFLUENCE LINE PROBLEM a. Determine the maximum positive ordinate for  member DC.  b. Determine the…

A: