How would you interpret the results of proctor test? Use sketches, where necessary, to illustrate the points. that you make an illustrated response.

Q: 1. Provide at least two (2) examples of any civil engineering related problems that uses numerical…

A: Numerical approaches are used to approximate the answer to a problem when an analytical solution is…

Q: Transform the force (600 N) into a force passing through point (A) and a couple whose forces acting…

A: To transform the given force system into force-couple system as per the given requirements.   We are…

Q: 1.) Determine bar force members EB, EC, and DC using method of sections. You may not copy the…

A:

Q: The two bars are used to support load P. When unloaded, joint B has coordinates (0, 0). After load P…

A:

Q: A bar spring arrangement as shown in the figure is subjected to temperature rise given by Due to…

A: temperature rise given by

Q: 3.38 The resultant of the forces P1, P2, and the couple C is the force R = 12k N acting at point A…

A: Position vectors:OA⇀=150i+200j  mmCB→=150i-200j   mmOP⇀=150i+50j  mmVector of…

Q: 2. Find the moment of the 2kN force about point A and about point B 2m 2kN 1.50m 1.50m B.

A:

Q: ce produced in each rod. vertical deflection of the VP D (2)

A:

Q: samples shows w-14.6%, G intractor compli

A: Given: Mean value of test sample shows, ω=14.61=0.146Gs=2.81γ=18.2 kN/m3

Q: 2. Determine the maximum deflection of the simply supported beam using double integration method. E…

A: Given Data: E=200 Gpa I=65*106 mm4   It is asked to find out the maximum deflection of simply…

Q: At what angle 0 must the 400-N force be applied in order that the resultant R of the two forces have…

A:

Q: Problem 3 A soap bubble 62.5 mm diameter has an intenal pressure in excess of the outside pressure…

A: The pressure inside the soap bubble is higher than that of external/atmospheric pressure due to the…

Q: The yield strength for a mild steel specimen was found to be 250 N/mm2. Taking a factor of safety of…

A: Given data : Factor of safety=2.15Yield strength=250 N/mm2To find :Safe working stress

Q: Calculate ff. Properties = 13.1 kdes = 25.9 the d = 302mm bf = 203 tf A. warping Constant b. Warping…

A: Given: Section size: W 310 x 60 mm To find the sectional properties of the given section: a. Warping…

Q: Determine the two couponent s (@) and (P) of the force (R=500 lb) Q R= 500 lb 12

A:

Q: Aloose, uncompacted sand fill 6-ft in depth hasa relative density of 40%. Laboratory tests indicated…

A:

Q: 3. As part of a site investigation program for a residential development project you retrieved four…

A: AASHTO Classification: 1. Percentage of particles passing through sieve #10 = 35% 2. Percentage of…

Q: Mention two aspects to be mentioned in the blueprint. Give an example of each with a description.

A:

Q: SITUATION 3. 1, Determine the force in member BD 2. Determine the force in member EF 3. Determine…

A:

Q: Physics La magnitud de la fuerza F= 218 N, se aplica en el punto A y su línea de acción pasa por B.…

A:

Q: Determine the forces in members CH and CF. The forces are positive if in tension, negative if in…

A:

Q: 1. Explain the step by step method of designing a high gravity dam. (Hydraulic Structure)

A:

Q: 4. The wide of the dam is x m. a.Find the hydrostatic force on surface AB and its moment about C.…

A: Question is based on the gravity dam . Width, Height and specific gravity of dam are given in the…

Q: A Three rods of equal length L and cross section area A, made of material Aluminum, rubber, steel…

A: Three rods made of different material but having equal length L, area A and load F. We need to…

Q: 12. Two cars of the same mass run head-on into each other at C. After the collision, brakes locked…

A: The given data is shown below:

Q: Describe how groundwater is affected by the following terrains: permafrost, desert, and the ocean…

A: Answer Introduction Groundwater is the largest reservoir of liquid fresh water on Earth and is found…

Q: 2. Determine the force in members BC, BE and CE of the truss shown using method of sections. 130 Ib…

A:

Q: Determine the magnitudes of all pin reactions for the frame loaded as shown. 800 N 295 mm OC B 625…

A:

Q: SITUATION 17 An I-beam beam has the cross section, 100mmx20mm top flange, 60mmx20mm bottom flange…

A: Fy = 250 MPaDeterminea. Location of plastic neutral axis from thr bottom.b. Plastic moment…

Q: Determine the force in members ED, EF, DF and DC of the truss and state if the members are in…

A: Given:- A truss member is given a two-point load  The magnitude of the point load 1 (P1) = 800 lb…

Q: Use Area-Moment Method. E = 200 GPa and I = 100 x 10° mm“. Compute the rotation at the free end in…

A:

Q: A square column with side dimension of 60 mm rests on top of a timber footing. It is determined that…

A:

Q: 2- Find the buckling load of the pinned-fixed stepped column shown below. a L/3 21 2L/3 2P

A: Euler's critical buckling load:Where;E - Young's modulusI - Moment of Inertia Le - Effective…

Q: Problem No. 1 Given the technical description of a triangular lot ABC. Find the following: A) Length…

A: First we will draw bearing diagram

Q: For the state of stress shown in the below figure, normal stress acting on the plane of maximum…

A: The question is related with solid mechanics subject . In this values we are provided with two value…

Measuring site work, Excavation and Piling

Bid drawings typically include very little material about the precise requirements of site work operations, measuring site work and excavation work differs from measuring most other works on a construction project. The actual site work conditions are not provided and also the dimensions of the excavations are not known during the pre-construction phase. The precise measurement of the excavation and backfill of the earth material and topsoil is important for a contractor to decide upon the total cost required for the process. All the works should be carried out under OSHA (Occupational Safety and Health Administration) standards to ensure the safety of the workers.