How to creat Drive Shaft in (Siemens) SINUMERIK

Q: The Fink truss is supported by a hinge at A and by rollers on a 1 to 2 slope at B. The bracing bars…

A:

Q: Detrmine the speed of rotation of the output shaft in figure below and its direction of rotation…

A: Write the expression of the gear ratio of gears A and B.

Q: (C) STEP REAMER (D) BULLET REAMER (E) STRAIGHT REAMER (F) PLOTED REAMER 2004 DERSTANDING GAUGE 1.…

A: HL18-6HL- Pin basic part number18-PartII, class 2 cadmium plate

Q: The bar DA is rigid and is originally held in the horizontal position. The wires are made of A-36…

A: Given:Diameter of steel, d=0.05 inchDisplacement of D=0.075 inch

Q: e diameter

A: To find Outside diameter(d2)

Q: Define Straddle hubs.

A: A straddle is a trading strategy that involves options.

Q: What is the minimum displacement of a gear motor turn ing at 800 rev /min if the flow rate to the…

A:

Q: how to design shaft based on critical speed for agitator?

A: Design of shaft for agitator:- .Tip speed- it is defined by speed of the agitator's blade tip or…

Q: A cast-iron gear with 100-mm effective diameter and t = 40-mm hub engagemen length is to transmit a…

A: Given: R - 10 mm t - 40 mm T - 120 N.m ro - 50 mm Ec - 100 Gpa Es - 200 Gpa f - 0.16  v - 0.3 To…

Q: Define drive head

A: Given Data⇒ drive head Problem statement⇒ Problem says Define drive head

Q: (f) The car drives down a hill of gradient 1 in 5 at a constant 110km/h. What power is required?…

A: Solution to sub-part (f) as mentioned by the student:   given: Effective mass of car = 1850 kg…

Q: Two Identical 45-kg cylinders A and B are supported by smooth planes. Determine ll reactions (in…

A:

Q: How to compute the friction in a screw drive

A: The ball screw mechanism is used in the CNC machining transmits the forces and moves the component…

Q: Define the term Torque?

A: Torque: Torque is defined as the multiplication of the force and force-distance from the given…

Q: Write the compatibility equation. Give consideration as to how it supports constrain shaft when it…

A: The compatibility equation make restriction to obtain how a strain can vary in a body for an assumed…

Q: 8(unich is The best-sited material for Commutator Segments.

A: Given Data⇒Commutator segmentsProblem definition⇒Problem says which is best suited material for…

Q: Part A If the radius of the fillet weld connecting the shafts is r =13.2 mm, and the allowable shear…

A:

Q: ) What machine that has a shaft with a minimum of three (3) [bearings, pulley, sprocket, gear,…

A: given:

Q: Describe the noncircular shafts?

A: The non-circular shafts are ones that do not have a circular profile and the shear stress for the…

Q: Make the definition of Spring Pin and what are the advantages and disadvantages

A: Spring Pin: It is an mechanical fastener. Spring pin is used to tight the relative positon of  two…

Q: Define the term Internal Torque?

A: Torque refers to tension and Based on the tension created the torque classified as…

Q: Make a Drive Shaft in SINUMERIK (ste

A: A drive shaft is a vehicle shaft that transmits power from the transmission to the wheels. The…

Q: Define the term Shaft Design?

A: Given Shaft design To find Definition

Q: What is the LMC of shaft C?

A: The Least material condition (LMC) tells about the minimum material can be used to produce the…

Q: (A) Two buses start at the same time towards each other from terminals A and B, 8 km apart. The time…

A: (A) given : for Bus-x : ( A to B) tₓ = 8 minutes = 8*60 sec   for Bus-y : ( B to A) ty = 10 minutes…

Q: why the number of disk is 17-1?

A: Given data:- Number of disc in one shaft (n1)=8 discs Number of disc in another shaft (n2)=9 discs…

Q: Outline four applications of shafts

A:

Q: D1 Driver gear (D2) Driver gear 1248 rpm what are the CW speed and direction of D1? 10" 2" D2

A: The given data are: D1=12 inD2=2 inN2=1248 rpm

Q: 8-7. A boiler is constructed of 8-mm thick steel plates that are fastened together at their ends…

A:

Q: If a spline is transmitting 2,000 lb-in torque, what would be the major spline diameter for a 4A…

A:

Q: gears il module is 4 and no

A: given:T1=25T2=75module m=4

Q: all of a drying oven is construc ctivity k = 0.0705 W/m-K betw ature, T₁= 450°C, and the com

A:

Q: What is the MMC of shaft "C"?

A: MMC stands for Maximum Material Condition, which is the feature of the size of the object that…

Q: How do you select a shaft for small sprocket in your chain drive?

A: Given question:   How do you select a shaft for small sprocket in your chain drive?

Q: Q2+ State adantages of Gyeloidal Involute profile gear tooth pufile. as a

A: Advantages of the cycloidal gear tooth profile: There are some advantages of cycloidal gear tooth…

Q: Q- The reduction of speed from 360 rpm to 120 rpm is desired by the use of a chain drive. The…

A: The reduction of speed from 360 rpm to 120 rpm,So, speed N1=360 rpm,N2=120 rpm,The driving sprocket…

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.