How much heat must be removed from 597 g of water at 38.0°C to change it into ice at -10.0°C? The specific heat of ice is 2090 J/kg K, the latent heat of fusion of water is 334 kJ/kg, and the specific heat of water is 4186 J/kg K.

How much heat must be removed from 597 g of water at 38.0°C to change it into ice at -10.0°C? The specific heat of ice is 2090 J/kg K, the latent heat of fusion of water is 334 kJ/kg, and the specific heat of water is 4186 J/kg K.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

There is an 500g container made out of aluminum holding 300g of water. The Water and Aluminum have reached thermal equilibrium at 40 degrees Celsius. A 200g block of iron at a temperature of 0 degrees Celsius is later dropped into the water. Using the specific heat for water=4180J/kg/C. The specific heat for aluminum is 900 J/kg/C. The specific heat for iron is 450 J/kg/C. The final temperature of the three materials will be degrees celsius. The thermal energy of the water changes by Joules. (give an amount and include a + if it increases and a - if it decreases) The thermal energy of the aluminum changes by Joules. (give an amount and include a + if it increases and a - if it decreases) The thermal energy of the iron changes by Joules. (give an amount and unit and include a + if it increases and a - if the value decreases)
An ideal gas of 4kg mass (MW=3g/mol and k=2.3) contained in a regulated mass system went through three processes in a cycle, one after the other. The initial conditions for the gas were 20kPa and 310K in the first step, and the pressure was isometrically increased by 30kPa. The gas was heated to 400 degrees Celsius using a technique defined by the equation PV3=C. Upon returning to its previous state, it exhibits polytropic behavior. Calculate the change in entropy for each of the processes.
Steam at a rate of 200 kg/min enters a turbine at 350°C and 40 bar through a 7.5-cm internal diameter pipe. The turbine operation is adiabatic, and the effluent leaves as saturated water at 5 bar through a 5-cm diameter pipe. 1. Calculate the work produced by the turbine in kW. 2. What is the enthalpyand phase of the effluent stream? 21 If it leaves the turbine at 75C and 5 bar 22 If it leaves the turbine at 30C and 5 bar 7.5
3000 kJ of heat is given to 1 kg of water at 20 C. If steam with a pressure of 750 kPa is obtained as a result of this process, is this steam wet?institution? You should reach the result by typing the table values and operation steps. TIP: You should decide on enthalpy values using Thermodynamic Property Tables.
Ice at -10°C and water vapor at 130°C are brought together at atmospheric pressure in a perfectly insulated container whose heat capacity can be neglected. After thermal equilibrium is reached, the liquid phase at 50°C is present. Ignoring the equilibrium vapor pressure at 50°C, find the ratio of the mass of the steam to that of the ice (L, = 3.35×10°J/kg L, = 2.26x10° J / kg C = 2000J / kg - °C cm = 2020J / kg -°C)
A copper container of mass 0.080 kg and specific heat 387 Jkg-1 K-1 contains 0.30 kg of water and 0.040 kg of ice at 0˚C. Steam at 100˚C is passed into the water and its temperature stabilizes at 20.0˚C. Find the mass of the water left in the container. Assume the system is insulated from its environment.
2. In a free-moving piston-cylinder assembly with a pressure of 60 kPa and a temperature of -20°C100 grams of R-134a is initially retained. until the assembly temperature is 100°C.is heated. Calculate the volumetric change after heating.
(a) An incoming stream of 1500kmol/min consists of saturated water with 65% liquid water and 35% steam at 40 bars. This steam is heated at constant pressure to 600°C. Using the steam tables, what is the heat transfer requirement for this step in kW? (Note: Steam tables in the bottom page)(b) This steam is then compressed isothermally to steam at 200 bars in a second step. What is the heat transfer requirement for this step in kW?
3.2 Carbon dioxide (Cp = 871 J/kg.K and Cv = 678 J/kg.K) is compressed from 0.4 m3 at 100 kPa and 14 oC to 0.08 m3 and 690 kPa according to the law PVn = Constant. Determine:(a) The value of the index n(b) The work done during compression(c) The change in internal energy(d) The heat transferred through the cylinder wall, stating whether this is a gain or loss
A soup is set to boil. When the soup reaches 170°F, remove it from the heat and set it on the kitchen counter. The air in the kitchen is 80°F, and the soup in the bowl is 120°F after two minutes. After removing the soup from the heat, how long will it be 90°F?
Calculate the amount of heat added to heat 1.2 m3/s of air at 18 C and 90%RH to 45 C without the addition of moisture using the thermodynamic properties of air. Barometric pressure is 101.325 kPa. (Do not use the psychrometric chart)