How much heat is required to convert (5gm) of ice at (-5C") to water at (50C") where specific heat of ice is (2.11 J/gm deg) and specific heat of water is (4.186 J/gm deg) and latent heat of fusion is (334.8 J/gm).

How much heat is required to convert (5gm) of ice at (-5C") to water at (50C") where specific heat of ice is (2.11 J/gm deg) and specific heat of water is (4.186 J/gm deg) and latent heat of fusion is (334.8 J/gm).

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter20: The First Law Of Thermodynamics

Section: Chapter Questions

Problem 20.10OQ: A 100-g piece of copper, initially at 95.0C, is dropped into 200 g of water contained in a 280-g...

See similar textbooks

Similar questions

Most automobiles have a coolant reservoir to catch radiator fluid than may overflow when 1he engine is hot. A radiator is made of copper and is filled to its 16.0L capacity when at 10.0C. What volume of radiator fluid will overflow when the radiator and fluid reach their 95.0C operating temperature, given that the fluid’s volume coefficient of expansion is =400106/C ? Note that this coefficient is approximate, because most car radiators have operating temperatures of greater than 95.0C.
(a) Estimate the specific heat capacity of sodium from the Law of Dulong and Petit. The molar mass of sodium is 23.0 g/mol. (b) What is the percent error of your estimate from the known value, 1230 J/kg ? `
Under what circumstances would you expect a gas to behave significantly differently than predicted by the ideal gas law?
A firewalker runs across a bed of hot coals without sustaining burns. Calculate the heat transferred by conduction into the sole of one foot of a firewalker given that the bottom of the foot is a 3.00-mm-thick callus with a conductivity at the low end of the range for wood and its density is 300 kg/m3. The area of contact is 25.0 cm2 the temperature of the coals is 700 , and the time in contact is 1.00 s. Ignore the evaporative cooling of sweat.
Even when shut down after a period of normal use, a large commercial nuclear reactor transfers thermal energy at the rate of 150 MW by the radioactive decay of fission products. This heat transfer causes a rapid increase in temperature it the cooling system fails (1 watt 2 1 joule/second or 1W=1J/s and 1MW=1megawatt ). (a) Calculate the rate of temperature increase in degrees Celsius per second (C/s) if the mass of the reactor core is 1.60105kg and it has an average specific heat of 0.3349kJ/kgC. (b) How long would it take to obtain a temperature increase of 2000C, which could cause some metals holding the radioactive materials to melt? (The initial rate of temperature increase would be greater than that calculated here because the heat transfer is concentrated in a smaller mass. Later, however, the temperature increase would slow down because the 5105-kg steel containment vessel would also begin to heat up.) Figure 14.32 Radioactive spentfuel pool at a nuclear power plant. Spent fuel stays hot for a long time. (credit: U.S. Department of Energy)
In 1993, the U.S. government instituted a requirement that all room air conditioners sold in the United States must have an energy efficiency ratio (EER) of 10 or higher. The EER is defined as the ratio of the cooling capacity of the air conditioner, measured in British thermal units per hour, or Btu/h, to its electrical power requirement in watts. (a) Convert the EER of 10.0 to dimensionless form, using the conversion 1 Btu = 1 055 J. (b) What is the appropriate name for this dimensionless quantity? (c) In the 1970s, it was common to find room air conditioners with EERs of 5 or lower. State how the operating costs compare for 10 000-Btu/h air conditioners with EERs of 5.00 and 10.0. Assume each air conditioner operates for 1 500 h during the summer in a city where electricity costs 17.0 per kWh.
How many grams of coffee must evaporate from 350 g of coffee in a 100g glass cup to cool the coffee from 95.0C to 45.0C ? You may assume the coffee has the same thermal properties as water and that the average heat at vaporization is 2340kJ/kg(560cal/g). (You may neglect the change in mass of the coffee as it cools, which will give you an answer that is slightly larger than correct.)
Assume you are measuring the specific heat of a sample of originally hot metal by using a calorimeter containing water. Because your calorimeter is not perfectly insulating, energy can transfer by heat between the contents of the calorimeter and the room. To obtain the most accurate result for the specific heat of the metal, you should use water with which initial temperature? (a) slightly lower than room temperature (b) the same as room temperature (c) slightly higher than room temperature (d) whatever you like because the initial temperature makes no difference
A 100-g piece of copper, initially at 95.0C, is dropped into 200 g of water contained in a 280-g aluminum can; the water and can are initially at 15.0C. What is the final temperature of the system? (Specific heats of copper and aluminum are 0.092 and 0.215 cal/g C. respectively.) (a) 16C (b) 18C (c) 24C (d) 26C (e) none of those answers
Compare the SI units of specific heat and latent heat and explain any differences.
If you add boiling water to a cup at room temperature, what would you expect the final equilibrium temperature of the unit to be? You will need to include 1he surroundings as pan of the system. Consider the zeroth law of thermodynamics.
Suppose a gasfilled incandescent light bulb is manufactured so that the gas inside the bulb is at atmospheric pressure when the bulb has a temperature of 20.0C. (a) Find the gauge pressure inside such a bulb when it is hot, assuming its average temperature is 60.0C (an approximation) and neglecting any change in volume due to thermal expansion or gas leaks. (b) The actual final pressure for the light bulb will be less than calculated in part (a) because the glass bulb will expand. What will the actual final pressure be, taking this into account? Is this a negligible difference?