How many identical resistors can be connected in series if the total noise voltage is 50  uV whose 10 uV noise voltage is provided by each resistor? Answer: N = 25 amplifiers

Q: 1. Perform the theoretical calculations to determine the Q-point for both circuits and compare them…

A:

Q: What is the power consumed by the 50Ohm resitor when it is connected in series with the 50V source?

A: When the resistor connected in series with the voltage source only then the voltage across the…

Q: If you know that value Ic=3.2 mA, VCE=5 v Determine R2

A: For the given circuit calculation the value of R2 :  IC=3.2mAVCE=5V Fr NPN transistor VBE=0.7V…

Q: + 20 2KS2 82m23 loss= 12mA Yp= -3V RS + 20 GIO Cs

A:

Q: • If the capacitor and resistive circuit is connected to a DC voltage, what will be the charging…

A:

Q: Q-A diode has a forward resistance of 2002 is connected in series with a resistive load of 10000.…

A: A half wave rectifier circuit as shown below- Forward resistance = 20 ohm, Resistive load = 1000…

Q: 6- What is the total resistance of the mixed circuits shown in the following Figure? Note that each…

A:

Q: Show the output voltage by drawing it through a period (The diode used is a silicon diode and it's…

A: A diode is a nonlinear circuit element. Approximate models are used for diodes to analyze…

Q: b) Figure 5 shows the silicon base BJT with a Rc = 1 kO, Rg = 10 kQ, Vcc = 11 V, VBB = 6 V, Boc =…

A: In this question we will find base , emitter and collector currents...

Q: Refer to the figure. The most probable cause of trouble, if any, from these voltage measurements is…

A:

Q: Q4/ /Using Norton's theorem, find the current through the branch a-b in the circuit shown. 120v 102…

A: Norton's Resistance is the resistance seen from ab terminals with current source open circuit and…

Q: In a common base connection, a = 0.95. The voltage drop across 2 k resistance which is connected in…

A: Give, The circuit is Here, V2kΩ=2 Vα=0.95

Q: 1. Build circuit R5 3,3KO 3.3KO R3 R4 R6 R2 4.7KO 10KO 4.7KO R1 1KO vs+ 50V-

A:

Q: For the potential divider shown in the figure, VIN = 10 V, R1= 10k and R2=4.7 k Calculate the output…

A: Ans

Q: Voe 19V Rc 100 n 15 k IGURE 5-42 32. The base bias circuit in Figure 5-42 is subjected to a…

A: Bias current- Bias current is referring to the prime power that is used to basically turn on a…

Q: VTh is the O Short circuit voltage Neither open circuit nor short circuit voltage Open circuit…

A: In this question we will write about Vth...

Q: Explain this circuitin details EQU 3

A: Assuming the blue highlighted switch denotes "Switch ON" mode. and not highlighted switch denotes…

Q: %237: If the frequency of the input signal is increased to 250 kHz, what happens to the output? You…

A: According to question: Let frequency of signal be 50Hz. ∴T=150⇒T=20ms Now if frequency is increased…

Q: What is the voltage across a 50 mH inductor if it takes a current of 100sin(100t) mA? -500cos(100t)…

A: According to the question we have to calculate the value of current voltage.

Q: Find the peak current of a series RLC circuit with the following parameters: source voltage= 10Vpk…

A: Source Voltage Vs=10 v (p-p)Frequency f=100 HzR=510 ΩC=22 μFL=1 H

Q: what is the total resistance

A:

Q: 16kv-4wire circuit has 150 amps on A at zero degrees, 160 on at 120 degrees and 170 amps on at 240…

A: Since it is 4 wire system. So type of load will be star connected.Now equivalent circuit can be draw…

Q: For a certain p-channel JFET, VGS(off) = 6.6 V. The value of VGs in V for midpoint bias is Round…

A:

Q: Determine the output voltage for the circuit in the figure for each input voltage waveform. Also,…

A:

Q: Calculate the efficiency of a class B amplifier for a supply of 15 V and an output of Vm(peak)=10 V.…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: A LED which bright one color when forward and another color on reverse is called One directional LED…

A:

Q: Draw the output waveform and include the voltage value. +50 V R 3.3 k -50 V www Vout

A: given circuit

Q: For a simple resistive potential divider, the CRO rating of oscilloscope is 250 V. For the…

A: Given: V0=250 VAmplification range=1050-1175  Apply voltage divider rule:…

Q: Answer the following Questions referring the circuit in figure 10. ID E-8V + VD- ✈ Si IR R2.2 k2 VR

A: Given,

Q: Listen R₁ Vww 22 ΚΩ + R ww 150 ΚΩ (c) and (d) OV out DE out (b) The circuit or circuits with a…

A: It is asked to find the circuit with virtual ground

Q: After bridge balance, the value of current in the detector circuit is Rg 5V E D R_ O a. same in the…

A: bridge is said to be balanced if there no voltage across the detector unit .  current through the…

Q: Silicon diode and 1kΩ resistor are connected in series to the 5V DC source output. What is the…

A:

Q: -Analyze the circuit shown below and draw the output voltage waveform. R₁ ww 2V A -2V Si + A 5V R₁…

A: In this question We need to draw the output voltage waveform. Assume forward bias voltage drop of si…

Q: Q) For the Voltage -divider bias Configuration of Figure below deteemine @ IBe O Ico Veco D VC O VE…

A:

Q: What is the voltage across R1 if the P-N junction is made of silicon

A: When positive terminal of the battery is connected to p side and negitive terminal of battery is…

Power Amplifier

The power amplifier is an electronic amplifier designed to maximize the signal strength of a given input. The input signal strength is enhanced to a high enough level to drive output devices such as speakers, headphones, RF (Radio frequency) transmitters, etc. Unlike voltage / current amplifiers, the power amplifier is designed to drive core loads directly and is used as a storage block in the amplifier series.

Maximum Efficiency Criterion

In every field of engineering, there is a tremendous use of the machine and all those machines are equipped for their popular work efficiency so it very much important for operation engineers to monitor the efficiency of the machine, planning engineers to check out the efficiency of the machine before installing the machine and design engineers to design machine for higher efficiency than and then the utility will procure their products that will ultimately lead to profit and loss of the company. It indicates the importance of efficiency right from the initial stage as manufacturing units, intermediate stage as planning coordinators, and end-users stage as a utility.