How many degrees is 424g 65c 26cc ? O a) 158 degrees 18 minutes 34 seconds O B) 22 degrees 11 minutes 14 seconds OC) 318 degrees 60 minutes 60 seconds O D) 14 degrees 39 minutes 15 seconds O TO) 318 degrees 83 minutes 43 seconds

Q: 50 mm 10 kNm 250 mm 250 mm

A:

Q: 100w 200200" Lankenta y at pt c है

A: To determine deflection in the beam, we can use the conjugate beam method. In this method, a bending…

Q: . Situation: You are driving when suddenly you saw a cat crossing across the street, You applied the…

A: Given, Retardation = 8 fps^2 Braking distance S = 456 feet

Q: Critical duration ? U 3 3 R. 4 2 3 O 15 days 18 days 16 days 17 days

A:

Q: For the same two-span continuous beam in Problem 1, determine the moment at C if point C settles 1.5…

A: Given that :-The two-span continuous beam has following specifications :I = 300 E = 29000…

Q: Tank is 300mm x 300mm Table 12.2 Variable Head Results Trials Head, h₁ (mm) 1 2 3 200 150 100 Head,…

A: Trials Head, h1 (mm) Head, h2 (mm) h1-h2 Time (sec) Actual Q Theoretical Q Cd 1 200 150 1.89…

Q: 500 Gu Determ.ne the moment a bout Point 610 as Shown

A: Given that:

Q: Q2For the gable frame shown in fig. below, roof dead load = 60 KN/ m. Determine total static load…

A: Compressive stress is the force that deforms the material in a way that reduces the volume of the…

Q: 400 N 800 N B D E IC F2 m

A: Given  Concentrated loads of 400 N and 800 N are acting at B and D respectively.

Q: free-body diagram. Yo

A:

Q: 7. A short rectangular reinforced column shown is to be part of a long span rigid frame and will be…

A:

Q: Check the correct statements regarding the picture. * ALT HDG MDA 310 10 ▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬ 10 10…

A: The picture displaying shows, Air craft is perfectly aligned with the centre of the runway

Q: The following truss system is Pin Supported at Joint C and Roller Supported at Joint E. Joint B is…

A: As per guidelines we need to answer only first 3 subparts of question so please repost rest…

Q: Q/ The following sketch include inverting readings of some stations. Construct a table of complete…

A: Given data  Bench mark Inverted staff 3 change points

Q: tomm lo tromm Samm Ix = 1.04 * 10^6 Ix = 2.01 * 10^6 Ix = 1.01 * 10^6 Ix = 1.8 * 10^6

A:

Q: M a s s e s    o f   50g, 100g, and 200g  a r e    p l  a c e d   a t   t h e  30 cm, 60 cm, and 80…

A: Center of Gravity:The point at which the total weight of the body is assumed to be concentrated is…

Q: 3.24 Refer to the 15-ft high embankment shown in Figure 3.8. Embankments are generally constructed…

A: Given information:

Q: Compute the location of the geometric and plastic centroid

A: Plastic centroid: -It is defined as a point at which resultant force induced uniform strain…

Q: For the angular section shown in figure 11: Which of the following most nearly gives the moments of…

A:

Q: What is the range of reaction distances for a car traveling at 70 miles per hour? (Use the lower end…

A:

Q: Explain that how the ultrasonic sensor HC-SR04 can be used to measure distances. Also, draw the…

A: An ultrasonic sensor is a device that uses ultrasonic sound waves to calculate a distance to an…

Q: النقطة )س( متساوية؟ س 1/ تي لحظة عن 150mm150mm. 1200N 60 500N - 700N 60 150mm 150mm 0 1000N MO =…

A:

Q: A box girder has the singly symmetrical trapezoidal cross section shown in Fig. P.10.23. It supports…

A: Solution- Given, Vertical shear load = 500 KN

Q: Station BS BM1 2.565 1+100 prohle level 1+200 TP1 HI ? 33.562

A:

Q: What is the area of the below figure if you know x=32.7? (use Simpson's rule) 3个 30 28 32 31 Answer:…

A: Given The coordinates of different points and the distance between the coordinates x= 32.7

Q: A cannonball was fired from a Word War I cannon with a vertical component of the initial velocity at…

A:

Q: Problem 2 If torque T 600 N · m, calculate %3D 30mm radius (1) TĄ =? (2) Tmax =? 40mm Hint: watch…

A: Draw shear stress diagram:

Q: 138 106 R1 0.8 R5 RO.7 R3,5 0.8 R15.2 R16 10 س۲/ ارسم الشكل (6) باستخدام مفاهيم العمليات الهندسيـة.…

A:

Q: Complete the differential level notes shown and perform the customary arithmetic check. Show your…

A:

Q: What is the maximum applied load this structure can support before it fails due to yielding (i.e. if…

A: YOUR ANSWER: THE MAXIMUM APPLIED LOAD THIS STRUCTURE CAN SUPPORT BEFORE IT FAILS DUE TO YIELDING:-…

Q: 0 0 350- 6028mm 01775 175 00 600 fe' = 27 MPa M₁ = 60 KN M M₂ = 200 KN M Compute WSD!

A: Note: Since you have posted multiple questions, we will provide the solution only to the first…

Q: A distance with an actual (most probable) value of 882 has been measured 8 times. Which of the…

A: Given data, Most probable value of a distance = 882 m Tolerance = 10%

Q: Draw the axial, shear, and moment diagram for the frame below. Also sketch the qualitative…

A:

Q: During a consolidation test, a sample of fully saturated clay 3 cm thick (= h) is consolidated under…

A:

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A: Given data:

MATLAB

MATLAB software is a registered trademark, multi-model programming language, and numerical computing environmental system created by MathWorks. 'MATLAB' is the short-form of "Matrix Laboratory". The MATLAB software permits the utilization of matrix operations, graphical representation of data, execution of algorithms, development of user interface, and linking programs created in other languages. Even though MATLAB is developed mainly for numerical computing, there is an optional toolbox that uses a symbolic engine known as MuPAD giving access to all the symbolic computing abilities. In addition to this, a Simulink package delivers graphical multi-domain simulation and design that is model-based for embedded and dynamic systems. MATLAB users are spread worldwide across the world and use MATLAB extensively.