How many 3/4 - in A325 bolts in standard - size holes with thread excluded from the shea plane are required for the bearing - typ connection shown in Fig. ? Use Fu = 58 ksi and assume edge distanc to be 2 in and the distance center - to - center of holes to be 3 in . Assuu that deformation at bolt holes is a design consideration. Pu =300k (I RED )

How many 3/4 - in A325 bolts in standard - size holes with thread excluded from the shea plane are required for the bearing - typ connection shown in Fig. ? Use Fu = 58 ksi and assume edge distanc to be 2 in and the distance center - to - center of holes to be 3 in . Assuu that deformation at bolt holes is a design consideration. Pu =300k (I RED )

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

WT12 x 38 Longitudinal welds Given: Properties of WT12 x 38: A, = 11.2 in? y = 3.0 in. b = 8.99in. Use A992 Steel: F, = 50 ksi F = 65 ksi LL = 3 DL %3D %3D tw = centroidal distance bf A. Governing Ultimate Tensile Capacity based on Yielding of gross section Round your answer to 0 decimal places.
Problem 3. An un-equal leg angle L8x4x2 made of ASTM A242 steel (Fy = 50 ksi, Fu = 70 ksi) is used as a tension member and connected to a gusset plate as shown in Figure 2 (a to d). ASABINCAT SALLALALALALALALALAL w₁ Weld * Gusset Rate 3 (c) Longitudinal and transverse welds O 18x4x2 Gusset Plate Steel Type: A242 18x4x2 bolts: 3/4 dia. Steel Type: A242 T (d) Bolted connection (d) Calculate factored fracture strength of the tension member in Figure 2(c). (e) Calculate factored fracture strength of the tension member in Figure 2(d). (f) What is the maximum permissible length for this tension member?
A tension plate shown below is used to support suspended load "T". Gusset Plate- F, = 248 MPa Fu = 400 MPa %3D 200 mm a) Determine the allowable tensile capacity of the plate if L= 240 mm. (Assume weld strength is satisfactory).
20. determine the capacity of the details shown below.A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksit) what is the weld capacity perpedicular to the beam of the flange connection in kips? (2 decimal places)
.
Topic:Bolted Steel Connection - Civil Engineering *Use latest NSCP/NSCP 2015 formula to solve this problem The butt connection shows 8-22 mm dia. A325 bolts spaced as follows: S1 = 40 mm S3 = 50 mm t1 = 16 mm S2 = 80 mm S4 = 100 mm t2 = 12 mm Steel strength and stresses are: Fy = 248 MPa Fu = 400 MPa Allowable tensile stress on the gross area = 148 MPa Allowable tensile stress on the net area = 200 MPa Allowable shear stress on the net area = 120 MPa Allowable bolt shear stress, Fv = 120 MPa Bolt Hole diameter = 25 mm Questions: Calculate the allowable tensile load T, under the following conditions. a) Based on the gross area of the plate b) Based on the net area of the plate c) Based on block shear strength
16) what is the tensile yielding capacity of flange plate of the flange connection in kips? (2 decimal places) A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi
Load and resistance Factor design-tension members Q- Look into the block shear failure mode on the angle L4X4X linked to the 1-inch gusset plate with three 1-inch diameter bolts. Steel A36 is the substance.
Please correct answer otherwise dislike
A double-angle shape is shown in the figure. The steel is A36, and the holes are for 1/2-inch-diameter bolts. Assume the Ae = 0.75An. Section 2L5 x 3 x16 LLBB Determine the allowable tensile strength for ASD. Select one: а. 52.1 b. 104.2 c. 87.8 d. 43.9
The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole what is the: minimum spacing as per AISC code provisions maximum spacing as per AISC code provisions minimum edge distance as per AISC code provisions maximum edge distance as per AISC code provisions
Two plates each with thickness t=16mm are bolted together with g-22 mm dia•bolts forming a lap connection.bolts spacing are as follows S1=40mm, S2=80mm,S3=100. Bolt hole dia=25 mm Fu=483Mpa Fy=345Mpa Solve the allowable strength and the ultimate strength in: 1. Yielding 2.rupture 3.shear 4.block shear