How does road transportation benefit the industry?

Q: Determine

A: The stresses acting on the planes are as follows:

Q: Problem 2: The footing shown on the next carries a 40cm '40cm column. For the soil profile shown…

A: Solution Given Diagram

Q: FHD = 50 m : LEH = 120 m a. b. Solve for the volume of free haul. Solve for the overhaul volume.

A: Given: Station End Area, m2 Cut Fill 2+00 0   2+020 15   2+040 30   2+060 0   2+080…

Q: 5. The beam supports the 80-kg load and is supported by the pin at A and a cable which wraps around…

A:

Q: Reduce the set of municipal cross-section notes in Table 2-8.

A:

Q: In Fig. E3.3–3, rigid bar ABC is supported by axial member (1), which has a cross-sectional area of…

A:

Q: A concrete pile with 20 m embedded length having 50 cm diameter is driven into a homogeneous…

A: Length of the pile, L = 20mDiameter of the pile, D = 0.5mCohesion, Cu = 30kN/m2Adhesion factor,  =…

Q: A plate 0.05 mm distant from a fixed plate moves at 1.2 m/sec and requires a shear stress of 2.2…

A:

Q: The level of water in the reservoir is 1.25 m. If there is a rainfall of 38 cm occurring in a month,…

A: Given Rainfall = 38 cm Water level = 1.25 m =125 cm Class A pan pan evaporation=32 cm Level of water…

Q: Q12) Calculate the ultimate soil bearing capacity for the (1.0 x 1.2 m) footing shown in Fig. (12)…

A: To calc :

Q: Consider the following data for concrete with mild exposure Water-cement ratio = 0.50 Water = 191.6…

A: Given data- Water cement ratio=0.50, Water = 191.6 litres, To Find- The cement content.

Q: *The factor of safety against overturning The factor of safety against sliding *Calculate the…

A:

Q: Help me please badly need

A:

Q: The accident investigation is a legal requirement. It also aims to prevent a repetition of the same…

A: to find  ans of given question

Q: Q1: Draw the shear force diagram for the shown loaded beam and write all the required equations. 10…

A:

Q: 1 A hydraulic jump takes place in a triangular channel of vertex angle 90°, as shown in figure. The…

A:

Q: Q6) Define the following words. 1-Optical Square 2-Bench Mark (B.M)

A: Surveying:-  The survey is a science or art to locate an unknown point with respect to a known…

Q: Help with Part (c) please

A: Elongation in the bar is given as 0.475mm Elongation in the is the sum of individual component of…

Q: A rectangular beam 300 x 600 mm cross section is subjected to bending moment of 50 kNm. The tension…

A: Given: A rectangular beam 300×600 mm cross section. Subjected to bending moment of 50 kNm. The…

Q: ituation 4: Three layers of soil are shown with the corresponding values of coefficient of…

A: Q. 7 & 8 has some missing data or content. But Q. 9 & 10 can be answered from the given…

Q: A compound horizontal curve is provided in the figure below. I1 = 72°00'". I2 = 58°00'. BC station…

A: A compound curve is given, with different radii R1 =500 ft and R2 = 750 ft The stationing of the…

Q: 64 £1,141 ATAPORTT est well penetrates 27 m below the static water table. After 24 hours of sec, the…

A:

Q: Define Alidade.

A: Draw the figure.

Q: What is the Maximum moment in kN-m. Given: w 17, a-2, b-4, and c-3. w kN/m am- bm ст

A:

Q: A pile is driven into the ground with a drop hammer weighing 1200 kg and having a free fall of 2.0…

A: Given data- Weight of drop hammer W=1200 kg, Free fall H=2 m=200 cm, Penetration S=1 cm, To Find-…

Q: Question 22 B, Hydrology- Over a basin of area 333 km², there was a storm for 6 h with a uniform…

A:

Q: The axis shown in the figure is supported by a thrust bearing in A and a pillow block in B. Draw the…

A: Compute the support reactions:Using the equilibrium condition:

Q: Define BIM.

A: Building Information Modeling (BIM) is defined as the 3D model-based process which digitally…

Q: At a point in a machine component that is subjected to plane stress, the normal and shear stresses…

A:

Q: Uge The Area- deflechien abor <how below

A:

Q: Question The focal length of the object glass of a tacheometer is 200 mm, the distance between the…

A: Focal length, f = 200 mm.Middle staff intercepts, s = 2 m,Spacing between upper and lower lines i =…

Q: 1. What are the types of wood products used to frame heavy timber buildings?

A: "Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: External support reactions: RA= RC = RF = KN KN KN The shear and moment at point B are The moment at…

A:

Q: (1.181 x 10-5 in.) and a crack length of 4 x 102 mm (1.575 × 103 in.) when a tensile stress of 160…

A:

Q: If the declination of a star is 70°10'N and the latitude of the observer is 49°50'N, then the values…

A: Given - Declination = 70o10' N Latitude  =  49o50'N To find -  The values of the star at the zenith…

Q: 4. 5. 6. Height of the capillary rise in the silt. b 3.33 m 13.33 m a. b. Vertical effective stress…

A:

Q: The short tangent of the spiral curve is 58.6m. The spiral angle at S.C is equal to 12°. Determine…

A:

Highway Safety

Proper highway safety refers to the methods or rules that prevent highway travelers from being killed or severely injured. Proper highway safety measures help to protect motorists, cyclists, pedestrians, passengers on public transport, and so on.