Problem#2 A level scaffold is to be supported at the center of a 12-ft ladder, as shown below. 1. Determine the required length x 2. Determine the angle 0. Required length x 1. 4.53 2. 6.63 3. 3.56 4. 7.58 Angle 0 1. 36.4 2. 40.6 3. 56.4 4. 50.8 TWI X 12¹ ladder Scaffold

Q: Question Attached

A: The factor of safety using method of slices along the trial surface. FS=∑c'l+W/bCos α-ultan…

Q: 3. What FS reading is required to set the top of the wall form to the correct elevation? EL= 99.599…

A: Calculate the FS reading to set the top of the wall form to correct elevation. Here we have…

Q: 5. It is desired to determine the height of a church steeple. level, a 500.00 ft length is measured…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: 450 N 30⁰ B 30° MATHalino.com C 450 N MATHalino.com 30°

A:

Q: 3.a. A buried cable installation will use a duct with a diameter of 8 cm. Three cables, each with a…

A: KINDLY NOTE: As per our guidelines we are supposed to answer the first question n case multiple…

Q: The gravity wall is made of concrete. Determine the location of the center of gravity (G) for the…

A: To determine the centroid of the dam.

Q: It is known that a vertical force of 181.9 lb is required to remove the nail at C from the board. As…

A:

Q: or this section, the geometry and sub-section shear forces are shown, when an applied shear force of…

A: Shear center location is independent of transverse force direction and magnitude. When a beam has…

Q: Hello, this is a combined footing exercise, can you help me get the bending moment and shear force…

A: It is important that any body should be in the state of equilibrium to come up with a shear and…

Q: 12.5 For seismic design purposes, where is the building base? • The level where the building columns…

A: given data:   for siesmic design purposes, where  is the  building base? a) the level  where the…

Q: Find the maximum value of load P without causing overturning of the wall having unit weight of 50…

A: Given: Unit weight of wall = 50 psf Width of wall = 10 ft Height of wall = 25 ft Factor of safety =…

Q: Explain Mode of deflection and lateral pressure distribution for sheeting supporting a vertical cut.

A: Sheet piles are used to retain the sand and clays i.e. soil  present on the side of cut. They are…

Q: Compute the force acting on a 5 m diameter gate which is inclined 60° from the vertical if the…

A: Diameter of the gate = 5 m Gs = 1.03  Height of sea water above the gate = 6 m Inclination from…

Q: ↑ LIM 93.34 KN 0.90m + 0.40m, 11.31 KN ↑ W = 53,52 x 1₁2 = ↑↑↑↑ ↑ ↑ 64.22 KNM⇒ 65 KNAM

A: A beam is given we need to find out the shear force and bending moment diagram

Q: Check if the wall was built to retain a sandy soil for sliding and overturning

A:

Q: Civil Engineering 1. A parabolic arch supports an inclined roadway above a river as shown: 30%…

A:

Q: PROBLEM 1: Determine the mass of the heaviest uniform bar that can be supported in the position…

A:

Open Channel Flow

Open channel flow is a branch of fluid mechanics. It deals with the flow of fluid in an open conduit or free surface. In an open channel flow, gravity induces the flow of water whose surface is open to the air. This flow is free-falling rather than confined in rigid body conduits. The open channel flow depends upon two parameters that are the cross-section of the conduit and the velocity profile. Practical examples of open channel flow are streams, rivers, canals, and other drainage systems.In open channel flow, the cross-sectional area of at least one of the sides is exposed to air, and the surface of water faces atmospheric pressure. This flow is also known as free gravity flow. The cross-sectional area of the conduit can be either man-made or a natural channel. For instance, the flow in rivers and streams are natural conduits, and the flow in a canal and sanitary systems are man-made or engineered channels.