Hook's joint is used to couple two shafts together. The driving shaft rotates at uniform speed of 1000 rpm. Determine the greatest permissible angle between the shaft axes so that the total fluctuation of speed of the driven shaft does not exceed 150 rpm. What will be the maximum speed of the driven shaft?

Q: A gear reduction system consists of two gears: E and X. Gear E rotates clockwise with a constant…

A: Given data: αE=4.5 rad/s2ωE=7 rad/s Need to determine select the correct statement.

Q: A follower plate B holds a pair of 26-tooth planet gears C against a 20-tooth sun gear A. Each plan…

A:

Q: The Diameters of pulleys of belt drive and number of teeth on the gears 2 to 7 are indicated in the…

A: Given data:Number of teeth in the gear,T2=18T3=44T4=15T5=33T6=36T7=16

Q: The drawing represents a planetary reduction gear used in aeronautics. Calculate the speed of the…

A: Speed of motor: N3=1200 rpm and considering N1=0 (is fixed) Number of teeth: Z1=50 teethZ2=18…

Q: the displacement of link 4 if the crank (link 2 )is rotated 135 degree clockwise.

A:

Q: in a planetary gear train, the arm C caries two gears A and B and a compound gear D-E. The gear A…

A:

Q: For the gear train in a watch shown in the following figure. The teeth number are Z1=24, Z2=48,…

A: In general, a gear train is a mechanical arrangement of two gears on a single frame such that the…

Q: A 32-tooth pinion has a module of 3 mm, rotates 2400 rpm, and drives an 800-rpm gear. Determine the…

A:

Q: Gear 2: N2 = 25 teeth and Pd = 20 per in Gear 3: d3 = 3.5 in Gear 4: N4 = 28 teeth Gear 5: d5 = 4…

A:

Q: 4. For the gear train in a watch shown in the following figure. The teeth number are z, =20, z,-40,…

A:

Q: 2. Shafts A and B are connected by rolling cones and are turning in the same direction. A makes…

A: A shaft is a spinning machine element with a circular cross-section that is used to convey power…

Q: a) In the planetary gear system at above determine the speed of shaft A for an input speed of 1000…

A: The given number of teeth on each gear are, Consider the table shown below for the relation of the…

Q: Consider the gear/pulley mechanism shown below (top view). The gear on the lower left is driven at a…

A:

Q: 12. The gear A on the drive shaft of the outboard motor has a radius r = 0.5 in. and the meshed…

A: Introduction: In an assembly, a pinion is the smallest of two meshed gears. Depending on the…

Q: A wooden block(s) of mass M= 400 gram and m = 100 gram is the total mass just starts to move when…

A:

Q: i need the answer quickly

A:

Q: A 500 pound weight is attached to a cable that is being lifted by a 10 inch diameter drum.  The 48V…

A: GIven data: The diameter of the drum is d=10 in The weight attached to the cable is Ft=500 lb The…

Q: Assuming there is no slippage for the belt assembly below, Determine the following: (a) What is…

A:

Q: The lathe machine in the Central University of Technology mechanical workshop uses epicyclic gear…

A:

Q: The machine design has stated that a 2.5 kW electric motor with an input speed of 1000 RPM is needed…

A: Given Data The power of the electric motor is: P=2.5 kW The input speed is: N=1000 RPM Th overall…

Q: Find centre distance of the gear

A:

Q: A rolling cone with a center angle of 15° turning at 240 rpm makes external contact with the second…

A: Given data: The Center angle of the first rolling cone is 2α=15°, The revolution of the first…

Q: The Diameters of pulleys of belt drive and number of teeth on the gears 2 to 7 are indicated in the…

A:

Q: belt is on the steps either side of the center step. If the minimum speed is 40 rpm and the smallest…

A:

Q: The distance between two parallel shafts is 20 mm and they are connected by an Oldham's coupling.…

A:

Q: gearing arrangement suitable for this

A: Given; A motor is running at; N= 1440 rev/minMotor power is given to run the motor is;  P= 1.5…

Q: In the image on the right, there is a red gear G1 on the left with a radius of r1 = 2.81cm. Gear G1…

A:

Q: The double-reduction helical gearset shown in the figure is driven through shaft 'a' at a speed of…

A: The double-reduction helical gearset shown in the figure is driven through shaft 'a' at a speed of…

Q: The pinion (gear 2 on shaft a) rotates at 695 rev/min clockwise and transmits 1497 W through the…

A: Given:The rotational speed of the gear 2, The power transmission from the pinion gear to the output…

Q: The pinion (gear 2 on shaft a) rotates at 635 rev/min clockwise and transmits 1305 W through the…

A: Given:The rotational speed of the gear 2, The power transmission from the pinion gear to the output…

Q: Párt A Determine the velocity of the gear rack C. Express your answer to three significant figures…

A:

Q: In order to change the direction of rotation a planetary gear is fitted with a compound planet gear…

A: Given data, The gears 3 and 4 is compound gear. Power of the motor, P = 5 kW = 5000 W No of teeth of…

Q: 20-in diamete

A: L=239.637in  v= 1047.197ft/min

Q: Gear 2: N2 = 25 teeth and Pd = 20 per in Gear 3: d3 = 3.5 in Gear 4: N4 = 28 teeth Gear 5: d5 = 4…

A:

Q: The planetary gear train shown in the image below has 16 teeth on the sun and 50 teeth on the…

A:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.