Homework 4 H.W//4.1- The beam shown in figure below consists from steel and aluminum, find the maximum load that can be applied if the stress in steel not exceeding 80MPa and in Aluminum 30MPa. Est = 210GPa and EAlu = 70GPa 6m 3PkN/m Steel Aluminum Steel 100mm 40mm 220mm 40mm

Q: give an easy example of snyder's synthetic unit hydrograph

A: Synthetic Unit Hydrographs are used for those catchements which are located in remote areas because…

Q: What do you understand by mean sea level?

A: The datum for measuring elevation and altitude is known as the Mean Sea Level (MSL).

Q: Profile Level Notes: The elevation of BM A = 366.65' BS (plus sight) on BM A = 3.85' IFS (minus…

A:

Q: TECHNICAL DESCRIPTIONS Bearing S 22°06' E S72 20' W N 15°34' E N 30°09' E S 10°22' E S 17'47' W S…

A:

Q: 1/2x10ft

A: We are given: 1/2×10 ft   The given expression is equivalent to computing half the length of 10 f.

Q: Q5-) Explain the standard consistency Procedure? according to the guide manual No. 1042@2011.

A: The standard consistency of a cement paste is outlined as that consistency which is able to allow…

Q: Draw the sectional front view (front section) and draw the orthographic projection (sideand top…

A: Asked: To draw the orthographic projection views of the given object.   The orthographic projection…

Q: Determine Ix and Tx.

A: GIVEN- A PLANE FIGURE TO FIND- MOMENT OF INERTIA ABOUT X-AXIS AND CENTROIDAL AXIS.

Q: Show the quadrants of a circle and within the circle show  S 30° W

A:

Q: Mmax <=

A:

Q: Convert: 255°53'47.675" to grads.

A:

Q: Give the equation for Cunningham correction factor.

A: where C =correction factor λ =mean free path d = particle diameter An are experimentally determined…

Q: What is the area of the opening of a 7-inch round duct to the nearer tenthsquare foot?

A:

Q: Q1. Draw the plan and components of the given line diagram. Assume necessary any suitable data. W,…

A:

Q: Assignment 2.: A line CD, 60mm long, is perpendicular to VP and parallel to HP. It is 20 mm above…

A:

Q: detemine the x and y

A: answer = 4.03 in   explanation is given in below step

Q: can u get the

A:

Q: Consider the commercial steel pipe shown in (Figure 1). Determine the flow of methane at T = 68°F in…

A: Pressure Drop (ΔP) = 5 * 10^(-3) psiLength of the pipe (L) = 2600 ftDiameter of the pipe (D) = 1…

Q: Draw the plan and elevation of the given line diagram. W W.C V KITCHEN D, 2100×1200 3600x2800 BATH V…

A:

Q: Draw the plan and elevation of the given line diagram. W. W.C V D,+ 2100x1200 KITCHEN 3600x2800 BATH…

A:

Q: Define Tacheometry.

A: Tacheometry is a term related with surveying. Tacheometry is a method through which horizontal…

Q: Draw (A.F.).(S.F.) &( B.M.) diagrams for the following problems: H 12t 5m 4m 2 1 3m 5m 4m 3m

A:

Q: Define the By Bowle's method ?

A: Joseph bowle presented a method/Formula to Determine Modulus of Subgrade Reaction .The Mehod is…

Q: What is the zero circle and discuss the determination Of the zero circle? b.) What is the zero…

A:

Q: A line has a bearing of S 33 deg. 24° 54" E. What is its azimuth? Show diagram

A: The Azimuth of line A can be calculated by subtracting the given bearing to 180°. Calculation:…

Q: LINES Line 1-2 Line 2-3 Line 3-4 Line 4-1 BEARINGS N 78° 07" E $10° 26' E $ 81°53' W N 10°05' W…

A:

Q: diagram. 10kN.m 2m 3m (20+#ID)/2 KN 2m 5m 77 5kN/m B

A:

Q: A wall has an area of 75 sq ft. Find to the nearer hundredth square meter thearea of the wall.

A: Given:- area = 75 sq ft To find:- Nearer hundredth square meter thearea of the wall.

Q: How do I find the horizontal analysis

A: Horizontal Analysis of financial statements is an analysis method that represents the changes that…

Q: ftware Orcad cadence in detail?

A: A schematic editor (Capture), an analog/mixed-signal circuit simulator (PSpice), and a PCB board…

Q: 4. WHAT IS THE HEIGHT OF THE FLAGPOLE (H) IF THE Hi at point A is 1.45m and at point C is 1.66m, ß =…

A:

Q: 0 89' - Multiply 53/4" X 132'-7" 2'-9" X 59' 1" - 3 81'-8 1/4' "1 X 35' - 1/2" 95'-5" x 93'-5"

A: 4. 95′−5′′×93′−5′'95′−5′′Convert 5 inches to feet: 5÷12=512=0.4167So, 95+0.4167=95.4167…

Q: 1.00 - D 30° - Ø1.00 F Ø1.00 в 4.00 2.50 2.00 1.50 E 3.00 A 5.50

A: Absolute Coordinates system is where we show location by cartesian coordinate with reference to one…

Q: FIND THE SOLUTION (D3+7D² + 19D+13)y=D0 where x=0, y=o y'=2, y" = -12

A:

Q: How did you get -7.5x2+0.417x3 for M1? Thank you for answering.

A: The triangular load can be assumed to be superposition of a downward uniform load and upward…

Q: What is Uniformly loaded strip ?

A: Answer:- Uniformly loaded strip: A uniformly loaded strip is defined as that strip which is…

Q: izin 12 in 12 jan ELEVATION 1.5 id. W 14 X 90 2L3X2 X 1/2 SECTION

A: a)  To determine the design strength First calculate the net area of double -angle bar

Q: E Listen Profile Level Notes: The elevation of BM A = 522.17' BS (plus sight) on BM A = 9.25' IFS…

A: Required :- elevation of the STA 0+00?

Q: Evaluate the double integral S 2 – z – y dydz. O 0.82 O 1.04 O 0.67 O 0.92

A: To evaluate the given double integral.   Given: I=∫01∫01-x22-x-y dydx

Q: Convert 276°25’26” to mils and radians. complete solution pls. thank you

A: