Homework 1. Compute the maximum deflection of a 10" by 14" simply supported solid rectangular redwood (S4S) beam. The span length is 15 ft and the beam is subjected to a uniformly distributed load of 1000 lb/ft. The allowable deflection is 1/300 of the span length. Is the beam satisfactory? Redwood: E = 1300 ksi 10 × 14 (S4S): I = 1950 in.4 2. Compute the maximum deflection for the beam of problem 1 if the loading consists of one concentrated load of 5000 lb at midspan instead of the uniformly distributed load. The allowable deflection is 1/300 of the span length. Is the beam satisfactory?

Homework 1. Compute the maximum deflection of a 10" by 14" simply supported solid rectangular redwood (S4S) beam. The span length is 15 ft and the beam is subjected to a uniformly distributed load of 1000 lb/ft. The allowable deflection is 1/300 of the span length. Is the beam satisfactory? Redwood: E = 1300 ksi 10 × 14 (S4S): I = 1950 in.4 2. Compute the maximum deflection for the beam of problem 1 if the loading consists of one concentrated load of 5000 lb at midspan instead of the uniformly distributed load. The allowable deflection is 1/300 of the span length. Is the beam satisfactory?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.2.1P: A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The...

See similar textbooks

Similar questions

The rigid plate ABC shown in figure 2, was positioned on top of two identical steel posts, and the aluminum post was 0.1mm shorter than the steel posts at temperature of 50°C, if the allowable compressive stress in steel is limited to 120 MPa and in aluminum to 150 MPa, what is the maximum possible load P that can be supported on the rigid plate at temperature of 10°C ?
Please write the complete solutions and Legibly. Rate will be given! Do not just copy asnwers in CHEGG! Thank you :) A singly reinforced rectangular beam 270 mm x 430 is reinforced with 4-16-mm-dia. rebars with yield strength 420 MPa. If bar centroid is located 70 mm from the bottom edge of the beam and f'c = 21 MPa, calculate the design moment strength in kN-m. Write your answer with 2 decimal places only.
Please answer step by step
W3D 25 Y= 155 %31 1oow= 2500 KN 27=310mm X= 475 Z= 60 %3D 102=600mm
I need help with this one. Thank you.
Hi, can somebody able to answer this one? pls. i really need it. thank you.
I saw this question solved before, both on Chegg and Bartleby and it was WRONG! Please,if you do not know how to solve DO NOT COPY the wrong solution.Thank you!
Sub: Advance Reinforced Concrete design. Follow the ACI 318 design code for the design. Answer the question with all details. provide the drawings with all details. Don't Copy Paste from Other Solutions please. i will Upvote You Value Óf X1= 27.65 Value Of X2= 395 1- Design the beam BC of the frame shown in Figure 1 for bending moment and shear force according to ACI 318 code requirements. The concrete cover is 30 mm. Dead load and live loads are given in Figure 1. Provide all drawings in detail. Please do check for maximum and minimum flexural requirements, maximum and minimum spacing of the shear reinforcement. f=X1 MPa, fy=X2 MPa D.L.=5 ton/m L.L.= 3 ton/m 6 m 3 m
Compression Steel Given: The beam cross-section shown have the following cross-sectional properities: f'c = 4000 psi Find phi Mn.
Part A If P = 4 kN , determine the slope at A of the simply supported beam. The modulus of elasticity of the wood is E= 10 GPa (Figure 1) Express your answer with the appropriate units. HA ? OA = Value Units Submit Request Answer Figure 1 of 1 Part B Determine the deflection at point C of the simply supported beam. Express your answer with the appropriate units. P ? 100 mm Ac = Value Units 200 mm H.5 m--.5 m- -3 m Submit Request Answer
12. Assume a uniformly load simply support beam with a rectangular cross section. The width of the beam is fixed by other design considerations. Determine the ratio between the difference in depth required for an aluminum beam compared to a steel beam in order to obtain the same maximum deflection. MOE aluminum can be taken as 10,000 ksi, for steel as 30,000 ksi. The maximum deflection for the beam is 5wl*/384EI Factoring the deflection equations we can conclude that for equal deflection Eala = Esls where subscripts a and s represent values for aluminum and steel. The depth of must be times the depth of the
i need the answer quickly