HOME WORK For the simple distribution system shown in Figure below, use the probabilistic approach to find: a)the feeder reliability, by assuming that the reliabilities of the individual components are: Ral = Ra2 = Ra3 = Rcl =Rc2 Rc3= Ra and Rbl = Rb2 = Rb3 = Rb. b) Calculate the unreliability of the feeder if Ra = Rb = 0.9900. %3D BBI BB2 AI A2 BI B2 CI Circuit breaker C2 Isolator A3 B3 C3 Feeder F Eng. Tamador Almomani

HOME WORK For the simple distribution system shown in Figure below, use the probabilistic approach to find: a)the feeder reliability, by assuming that the reliabilities of the individual components are: Ral = Ra2 = Ra3 = Rcl =Rc2 Rc3= Ra and Rbl = Rb2 = Rb3 = Rb. b) Calculate the unreliability of the feeder if Ra = Rb = 0.9900. %3D BBI BB2 AI A2 BI B2 CI Circuit breaker C2 Isolator A3 B3 C3 Feeder F Eng. Tamador Almomani

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.13MCQ

See similar textbooks

Related questions

Q: Please answer this diligently. Other answers in the internet seems wrong. Please help me understand…

Q: 6. Fill in the following table U.S Power System Standards Fill in the table for a correctly wired…

A: U.S National Electric code for voltage and frequency would be 208 V (Line-Line ), 60Hz…

Q: Problem 2.. Determine the 3×3 bus admittance matrix Yous for the 3-bus circuit in the figure below.…

A: Given circuit diagram, YBUS =?

Q: In the outage replacement rate method, the repair rate is zero. Select one: True O False The…

A: We are answering all the questions. Solution of first question: Given statement is in outage…

Q: For a single phase full wave AC controller, the input rms voltage is V_{s} = 120V 60 Hz load is L =…

Q: The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltage minima is 80…

Q: The 100V source is absorbing 50w of power in the network shown what is the value of R and what power…

Q: The load flow data for the sample power system are given below. The voltage magnitude at bus 2 is to…

A: The first step in the Newton-Raphson method is to calculate the admittance matrix. The admittance is…

Q: quivalent pu reactance dia

Q: Example 9.7 A 50MVA, 11KV, synchronous generator has a sub transient reactance of 20%. The generator…

Question

HOME WORK
For the simple distribution system shown in Figure below, use the probabilistic
approach to find:
a)the feeder reliability, by assuming that the reliabilities of the individual
components are: Ral = Ra2 = Ra3 = Rcl =Rc2 Rc3= Ra and Rbl = Rb2 = Rb3 = Rb.
b) Calculate the unreliability of the feeder if Ra = Rb = 0.9900.
B/BI
B/B2
AI
A2
B2
CI
C2
Circuit breaker
Isolator
A3
B3
C3
Feeder F
Eng. Tamador Almomani
114
Eng. Tamador Almomani

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Solution of a

VIEW

solution of b

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
The load flow data for the sample power system are given below. The voltage magnitude at bus 2 is to be maintained at 1.04 p.u.Determine the set of load flow equations at the end of first iteration by using N-R method. Impedance for sample system Bus Code Impedances line charging admittance 1-2 0.08 + j0.24 0.0 1-3 0.02 + j0.06 0.0 2-3 0.06 + j0.18 0.0 Schedule of generation and loads: Bus Code Assured Voltages Generation Load…
The load flow data for the sample power system are given below. The voltage magnitude at bus 2 is to be maintained at 1.04 p.u.Determine the set of load flow equations at the end of first iteration by using N-R method. Impedance for sample system Bus Code 1-2 1-3 2-3 Schedule of generation and loads: Impedances 0.08 + j0.24 line charging admittance 0.0 0.02 + j0.06 0.0 0.06 + j0.18 0.0 Bus Code Assured Voltages Generation Load MW MVAR MW MVAR 1 1.06 + j0.0 0 0 0 2 1.0 + j0.0 0.2 0.0 0.0 0.0 3 1.0 + j0.0 0 0 0.6 0.25
In the following network, the voltage magnitudes at all buses are equal to 1 p.u., the voltage phase angles are very small, and the line resistances are negligible. All the line reactances are equal to j1 p.u. (1) (2. P₂ = 0.1 p.u. P3 = 0.2 p.u. The voltage phase angle 83 in radian at bus 3 is (Assume one of the generator bus as slack bus and sin-¹ (0.1) = 0.1 rad) (a) -0.1 (b) -0.2 (c) 0.1 (d) 0
Fill in the table for a correctly wired duplex outlet (U.S. National Electric Code standards for voltage PARAMETER EQUATION and frequency). Note the used of double- subscript notation. You can assume a 0° phase reference for Vba(t). Vba(t) Vea(t) Vbe(t) Vba (Peak Phasor) Vea (Peak Phasor) Vbc (Peak Phasor) Vba (RMS Phasor) Vea (RMS Phasor) Vbc (RMS Phasor) A C
A three-phase, 60-Hz, untransposed transmission line runs in parallel with a telephone line for 20 km. The power line carries a balanced three-phase rms current of Ia = 3202 – 240°A. The line configuration is as shown in figure. Assume zero current flows in the ungrounded telephone wires. Find the magnitude of the voltage induced in the telephone line. = 32020°A, Ī, = 3204–120°A, and a 4 m 4 m 5 m d G2 mO
4. A 4160V, three phase source, 4-wire supplying an unbalanced three phase load. The unbalanced connected load are: Zan = 150/53.13° ; Zbn = 150-53.13° ; Zen = 1500° Assuming positive sequence and the reference is the line voltage "a", determine: a. the line current "a" b. the line current “b” c. the line current "c". d. the total real power e. the total reactive power f. the total apparent power g. the overall power factor. h. the neutral current.
Problem 4- A large 3-phase industrial load draws 3.6 MVA at 0.85 power factor lagging from through a three- phase 12.47/7.2 kV 3-wire overhead distribution line. The phase conductor is #1 ACSR “Robin". Taking 3.6 MVA and 12.47 kV as base values, determine (a) The base impedance in (N) (b) The reactive power drawn by the load (p.u.) (c) The total current (p.u.) drawn from the power supply
Thanks
Write a report on the Star connection for three phase load experiment using the data/results from the experiment.
Please answer this diligently. Other answers in the internet seems wrong. Please help me understand and solve this problem. I'll give a like. Thanks!
help on this question? I just wanna check if I did the 5.15 right. The 5.14 has a solution in Barteby from the book Power System Analysis and Design by Glover and Sarma 6thEd. But the 5.15 hasn't