HiW.2 え-? static 14cm Ans. 文。1.6 Cm locm 5um 14cm 20 cm 133 CamScanner - W ia gal

Q: 2. If Tc= (-5) find TF. TK and TR.

A: Given:  TC=-5

Q: Horizontal beam AB is supported by pin A and cable BC as shown. Pin A is in double shear and has…

A: The yield tensile strength of 1045HR steel is, The shear strength of 1045HR steel is, To find the…

Q: The steel shaft is made from two segments: AC has a diameter of 50 mm, and CB has a diameter of 100…

A:

Q: The 1 inch diameter shaft is subjected to the loads shown. Draw the "loading diagram" showing the…

A: To findDraw the loading diagram showing the internal forces and moment/Torque acting on a cut…

Q: WHAT 16 THE NOMINAL RATE OF INTE REST COMPOUNDED CONTINOUSLY FOR IOYRS IF THE COMPOUND AMOUNT FACTOR…

A: Answer: The nominal rate of interest is 3.0455%.

Q: A mass, m of 22 kg consider one vertical motion only with angular displacement, 0 = wt, with spring…

A:

Q: find closure Eq.

A: You have mentoned the postions and angles .

Q: A power cycle produces 12 MW by partial conversion of the received heat as a result of steam…

A: Given Data Heat produce is :Q˙c=12 MW Saturated pressure is :Psat=1900 kPa Temperature of sink is:…

Q: solve/ show solution for given answer equations  kb = (Ab*Eb)/ g and kc = (Ac*Ec) / g

A: Given a bolted connection between two steel plates with specific dimensions and a torque of 57…

Q: A water stream at pipe AB divides into two branches as shown in the figure below. The average…

A: given data; ⇒diameter of pipe A (dA)=2inch=0.0508m⇒velocity in pipe (VA)=2m/s⇒diameter of pipe C…

Q: 04/ Determine suitable groove dimensions for a 0101-16 '0' ring to seal against a solid cylinder.

A: Given that ,  Determine suitable groove dimension for a 0101-16 'O' ring to steal against a solid…

Q: Determine the equivalent state of stress if an element is oriented 20° clockwise from the element…

A:

Q: Q/ The moment about the centre of the bolt is 0.2 m 0.03 m O 20.21 N.m O46.411 N.m O 55.626 N.m 300…

A:

Q: If rod CD is rotating with an angu lar velocity wcD= 16, determine the followings: Lengihs 43.1 60…

A: We are suppose to solve only 3 subparts. Please post other parts as a separate question.

Q: Select a suitable chain drive to transmit 50 kW from an electric motor to a line shaft. The motor…

A: Given dataP=50 KwN1=1200N2=250Speed ratio=N1N2=1200250=4.8a=600 mTo design the chain drive

Q: If rod CD is rotating with an angu lar velocity wcD= 16, determine the followings: Lengths: AR =40…

A:

Q: I Givin Bean Loaded Draw VtM diagrami as shown GI- Consbant 20ku/u Gokn A 080 4m

A: Given, The total length of the beam is L = 8 m

Q: с a 16 Griven p=20 a = 3 C = 8 whar is value of d?

A:

Q: The platform scale consists of a combination of third- and first-class levers so that the load on…

A: Given DataThe mass of the counter weight is: The acceleration due to gravity is: To DetermineThe…

Q: Sportsman with a mass of 90 kg at the end of the flexible springboard with a 1 m console 2 Hz…

A: We have to find stiffness

Q: In the moment calculation, why did you take away the h* from 8?

A:

Q: Convert from decigrams to pounds 4dg->1B Transfer from Dream to Desigram dcixss->dg Convert from…

A: 1. Convert from decigram to pound 1 dg = 14535.92371 dg = 0.0002204622621847756 lbso,4 dg = 4…

Q: 4. Determine the length of stroke of a slider E when the crank AC rotates by 30 degrees in counter-…

A: Find the attachment for the solution.

Q: the front view and side view of a hexagonal headed bolt for the

A: Given:  Diameter of the bolt = d= 40 mm, Width across flat= 1.5d +3 mm, Thickness of the bolt head =…

Q: The students are required to explain the following terms using the figures along with the…

A: Linear motion is the motion of the particle moving in the straight line. It is a one dimensional…

Q: Q// Determine the resultant force in figure bellow, and specify where it acts measured from point B.…

A:

Q: In the crank-slider mechanism below, what is the range of motion of the slider (the distance between…

A:

Q: Does this machine maximize or minimize the force (100 Ib) *

A: Reaction force acting on the point B is RB×1.5=100×20RB=1333.33 lb As the reaction force acting at…

Q: A wheel rest at the corner of the block as the figure. It F is a minimum force required to raise the…

A:

Q: What will be acceleration of point B for figure 1 with R-8, R2-2, R3-5, R-7, 02-40° wz-30 rad/s…

A:

Q: 3. Fxz²i + (1 - 3xy)j + yzk, A. xyi + 2yzj - 3yk B. zi + 2xzj - 3yk C. zi + 2zj3xk D. xi + 2yzj -…

A:

Q: Link AB is the input link, Link CD is the output link (follower), . (a) What the ratio of force…

A: (a) Draw the force diagram at point C.

Q: Given: L¡ = 7.25 in., L2 = 2.00 in., L3 = 7.00 in., L4 = 4.50 in., 01 = 5°, and 02 = 150°.…

A:

Q: grees sideways. AB-20, BC-25, CD-30, 8D-50, CF-4Scm. Draw in appropriate scale

A:

Q: Question No 3 Use both lIC method and regular (vector/scalar) method Given: ASF. Angular velocity of…

A: Given data: Angular velocity of link AB=10radsec

Q: y-axis 6m 6m >X-axis 12m

A: To determine the centroid of the given figure.

Q: Question 1) For the slider-crank mechanism. Solve Analytically for the position of the slider O4A.…

A:

Q: Knowing that the tension in wire BD is 1340.0 N, determine the reaction at the fixed support Cof the…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.