his I need help this I need help this Help with questic A3phese, 480V,60 Hzaesouredelivers 1000-At0707 power fecterlaggingte with this uestionconested leadestion. question. this question Heip w Telp with question Help with question Help with I need help this fet his quesesgging Find the capacitence perphasenecesseny teimprevethepowerfactorte this questionwith this questi this question Help with I need help question Find the-magnitude efthesoureeeurrentefteradding thecapaciter. Help with need help this I need help this Help w vith this question. with this question. with this this qu

Q: with this question Help with this question Help with question. with this I need help this Abeleneed…

A: Given, A 3-ph system has,  Active power (P) = 50 kW  Power factor = 0.85 lagging  Line voltage (VL)…

Q: thst SmA (^ FMA find VA

A:

Q: A 3 phase, 4 pole, 11 kV, 10,000 kVA alternator has neutral earthed through a resistance of 9 ohms.…

A:

Q: 2-8. The following voltage waveform is seen on an oscilloscope connected to the input of a length of…

A: Given below clear explanation

Q: The number of currents alternating at different time intervals in an alternating current circuit are…

A:

Q: The instantaneous current and voltage values for each 45 degree interval are shown in the table.…

A:

Q: QUESTION 13 L1 -S1 N7:112 S1 GRT GREATER THAN Source A Source B N7:112 Any value greater than 12 12…

A: Choose the correct answer:

Q: Complex power S in (VA)                                         S=______________ Power P in Watts…

A:

Q: What is the Voltage per Phase? O 4340 Volts O 4430 Volts O 4530 Volts O 4360 Volts

A:

Q: what would be the minimum size feeder conductor THHW 75 degrees for four 30- amp motor generator arc…

A: To find minimum size feeder conductor THHW 75 degrees motor generator arc welders = 4 numbers  , 30…

Q: A single phase load is located 2800 feet from its source. The Load draws a current of 86 A and…

A: A single phase load is located 2800 feet from its source. The Load draws a current of 86 A and…

Q: Determine la resistencia total y corriente total, así como la corriente, voltaje y po- tencia que…

A:

Q: Determine the total resistance and total current, as well as the current, voltage and power that…

A:

Q: Consider the circuit shown in (Figure 1). Suppose that 0 = 26°. Figure Source A 240√2/50° 10 www…

A: Power is given byP=(RMS voltage)*(RMS current)* power factorP=VI cosphieCurrent, I= (Va-Vb)/R+jX.

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.