Here are some of the Structural General Notes: I. SHOP DRAWINGS WITH ERECTION AND PLACE DIAGRAMS OF ALL STRUCTURAL STEELS, MISCELLANEOUS IRON, PRECAST CONCRETE ETC. SHALL BE SUBMITTED FOR ENGINEERS APPROVAL BEFORE FABRICATION. II. THE CONTRACTOR SHALL VERIFY ALL DIMENSIONS BEFORE ALL WORK IS TO BEGIN TO CHECK WITH MECHANICAL AND ELECTRICAL CONTRACTORS FOR CONDUITS PIPE SLEEVES, ETC., TO BE EMBEDDED IN CONCRETE. II. CONSTRUCTION NOTES AND TYPICAL DETAILS APPLY TO ALL DRAWINGS UNLESS OTHERWISE SHOWN OR NOTED MODIFY TYPICAL DETAILS AS DIRECTED TO MEET SPECIAL CONDITIONS. IV. IT SHALL BE THE CONTRACTOR'S RESPONSIBILITY TO PROVIDE ADEQUATE SHORING & BRACINGS OF THE STRUCTURE FOR ALL LOADS THAT MAY BE IMPOSED DURING CONSTRUCTION. Which of the statement/s can be used for other disciplines General Notes? A) II II None from the above D) II & IV

Here are some of the Structural General Notes: I. SHOP DRAWINGS WITH ERECTION AND PLACE DIAGRAMS OF ALL STRUCTURAL STEELS, MISCELLANEOUS IRON, PRECAST CONCRETE ETC. SHALL BE SUBMITTED FOR ENGINEERS APPROVAL BEFORE FABRICATION. II. THE CONTRACTOR SHALL VERIFY ALL DIMENSIONS BEFORE ALL WORK IS TO BEGIN TO CHECK WITH MECHANICAL AND ELECTRICAL CONTRACTORS FOR CONDUITS PIPE SLEEVES, ETC., TO BE EMBEDDED IN CONCRETE. II. CONSTRUCTION NOTES AND TYPICAL DETAILS APPLY TO ALL DRAWINGS UNLESS OTHERWISE SHOWN OR NOTED MODIFY TYPICAL DETAILS AS DIRECTED TO MEET SPECIAL CONDITIONS. IV. IT SHALL BE THE CONTRACTOR'S RESPONSIBILITY TO PROVIDE ADEQUATE SHORING & BRACINGS OF THE STRUCTURE FOR ALL LOADS THAT MAY BE IMPOSED DURING CONSTRUCTION. Which of the statement/s can be used for other disciplines General Notes? A) II II None from the above D) II & IV

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The person that’s accountable for designing the structural plans is known as a professional _____________________. The _____________________ and columns are critical components in the beginning stage of the project. The _______________ notes provides detail information about the grade of concrete and steel. The__________________ and alphabets [A-D] on a set of plans are used as reference points. Site plans are also knowns as ___________ plans. Label dimensions always win out or have precedent over measured dimensions. true or false The Scales usually used to design floor plan are 1/8” Thur 1’ scale. true or False
Q#3: Design Rcc slab for an Isolated Living room resting on masonry walls with following data: Room size = 12' x 26', Service live load = 40 psf , Roof Insulation = 25 psf , fc'=3 ksi , fy=40 ksi Note: Solve the problem on this sheet comment on steel spacing & diameter that you have selected from selection table A-4 already provided in design problems lecture Note: Write the answer in word format Subject: Reinforced Concrete Design 2
write in detail about different methods of pre-stressing. Also write about the erection methods for pre-cast units in detail.
1. Write Ten titles of textbooks about the design of Reinforced Concrete. 2. Write Ten titles of structural concrete journals.
Write in detail about different methods of pre-stressing. Also explain in detail about the erection methods for pre-cast units .
b) i. Timber has been one of the materials uses for the construction of roof. Explain with a short note on defects in timber due to defective seasoning and conversion. ii) Interpret the term preservation of timber and demonstrate different methods of preservation adopted. iii) Advertise short notes on defects in timber due to defective seasoning and conversion. vi) Explain with a short note on defects in timber due to defective seasoning and conversion.
Please answer ASAP! Rate will be given!
Discuss about the pre tensioning and post tensioning procedure in detail?
Write in detail about the single tee,double tee and hollow core sections in detail and shapes of pre-cast units.
Define drop hammers
Q.5: Write in detail about different methods of pre-stressing. Also write about the erection methods for pre-cast units in detail.
Write any differences between plain and reinforced concrete column.