heavy 50-m tape has a cross-sectional area of 0.05cm^2 and is standardized at a tension of 5.5kg and is of standard length at 20degree C. It is used to layout a runway 2,500.00m long. Determine the correct length to be laid out when the temperature is 42degree C and if a pull of 12kg is applied. E= 2.10 x 10^6 kg/cm^2 and the coefficient of linear expansion = 0.0000116/1degree C

heavy 50-m tape has a cross-sectional area of 0.05cm^2 and is standardized at a tension of 5.5kg and is of standard length at 20degree C. It is used to layout a runway 2,500.00m long. Determine the correct length to be laid out when the temperature is 42degree C and if a pull of 12kg is applied. E= 2.10 x 10^6 kg/cm^2 and the coefficient of linear expansion = 0.0000116/1degree C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The measured length of a line is 99.642 m using a 100-m steel tape supported at 0-25-55-100 intervals with the tape weighing 3 kg. The recoded tape temperature during the measurement is 34°C under a pull of 8 kg and the difference in elevation between endpoints is 0.50 m. The standard temperature of the steel tape is 27°C and the standard tension is 10 kg. Determine the correct horizontal line.
Show full solutions.
HWoDraw the shear Stress distribution diagram for the I-section beam with unequal flanges shown in figure? and Find max 6€ & o é. then drau bending Somm stress distriloulion. 25emm Ans/ Tmmt=7.36 MB louw Sommn- 250mm 2m 2m 2m Somm IS0 mm
hello how to determine the horizontal deflection of D
Example 4.3: Determine the shear resistance of a rolled channel section 229 x 89 Grade S275 steel loaded parallel to the web. Design shear force is 50kN. b Properties (Taken from Eurocode 3 Blue book-Design Data) IS CODE h = 228.6 mm b = 88.9 mm t₁ = 13.3 mm t₁ = 8.6 mm r = 13.7 mm A = 4160 mm² h tw
situation 31 A 468.0-m long boundary line is to be laid out with a 30.0-m invar tape weighing 0.70 kg at 20°C under a standard pull of 68.61 N supported at both ends. Modulus of elasticity of tape E = 205 GPa, tape cross-sectional area A = 3.71 mm, and coefficient of linear expansion a = 0.0000131/°c. If during measurement, the ambient temperature is 25°C and the tape is supported both ends under a pull of 63.0 N every 30-meter mark, determine the following: Total correction due to temperature, Cremp- Total correction due to pull, Cpall. Total correction due to sag, C.sg. The actual length of tape during measurement, in meters. i. ii. iii. iv.
A 467.0-m long boundary line is to be laid out with a 30.0-m invar tape weighing 0.70 kg at 20°C under a standard pull of 68.67 N supported at both ends. Modulus of elasticity of tape E = 205 GPa, tape cross-sectional area A = 3.77mm^2, and coefficient of linear expansion a= 0.0000131/°C. If during measurement, the ambient temperature is 25°C and the tape is supported both ends under a pull of 63.0 N every 30-meter mark, determine the following: Total correction due to temperature. Total correction due to pull. Total correction due to sag. a. b. C. d. The actual length of tape during measurement, in meters.
Situation 6: The pin is made of a material having a failure shear stress of Trail = 90 MPa. Determine the minimum required diameter (mm) of the pin to the nearest mm. Apply a factor of safety of F.S. = 1.9 against shear failure. Use P = 70 kN 무 P
If the resultant of the system is required to be minimum as possible, determine F1 along x
The measured length of a line is 99.642 m using a 100-m steel tape supported at 0-25- 55-100 intervals with the tape weighing 3 kg. The recoded tape temperature during the measurement is 34°C under a pull of 8 kg and the difference in elevation between endpoints is 0.50 m. The standard temperature of the steel tape is 27°C and the standard tension is 10 kg. Determine the correct horizontal line.
1. A typical cross-section of a roinforced concrete T-beam is shown in the figure below. The beam is reinforced with eight 25 mm diameter bars in tension zone. For the purpose of analysis, use the effoctive depth of 575 mm. Use f. = 25 MPa and f, = 420 MPa. Determine øM, 1000 mm T100 mm 8-D25 300 mm 575 mm ww G29
Ex-6. A steel tape with a cross-sectional area of 0.039 cm²and weighing 0.909 kg has a length of 30.009 m. when supported throughout 20°C and subject to a tension of 5.5 kg. This tape is used to measure a distance along a uniform 4% grade and is supported throughout during the measurement. The tension applied is 12 kg. The temperature of the tape is 2°C. The measured slope distance is recorded 381.615 m. What is the corrected horizontal distance? AMa