heat engine receives heat from a heat source at 1200°C and has a thermal efficency of 40 percent. The heat engine does maximum work equal to 500 kJ. Determine the heat supplied to the heat engine by the heat source, the heat rejected to the heat sink, and the tmeperature of the heat sink.

heat engine receives heat from a heat source at 1200°C and has a thermal efficency of 40 percent. The heat engine does maximum work equal to 500 kJ. Determine the heat supplied to the heat engine by the heat source, the heat rejected to the heat sink, and the tmeperature of the heat sink.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter44: Geothermal Heat Pumps

Section: Chapter Questions

Problem 1RQ: Geothermal heat pumps, or water-source heat pumps, are classified as either _____loop or _____loop...

See similar textbooks

Related questions

Q: A pulley is mounted on a 1.5in diameter shaft. Rotation is driven by a cylindrical steel pin with an…

A: shaft diameter d=1.5" yield strength of the pin Sy=18000psi torque applied T=250lb-in factor of…

Q: What does "viscous flow" mean, and what does "head loss through friction" mean? Describe the…

A: Viscous flow refers to the flow of fluids in which there is a resistance to motion due to the…

Q: Using the method of joints, determine the force in each member of the truss shown. State whether…

A: According to the given data A loading structure ABC We need to find Force in each member

Q: Pro 12 The tractor exerts a towing force of T=500 lb. There are two front and two rear tires which…

A: The tractor exerts a towing force of T-500 lb. There are two front and two rear tires. The tractor…

Q: A 1,000-N uniform boom at - 62.5" to the horizontal is supported by a cable at an angle of weight w=…

A: Given data is

Q: A 4 mm thick piece of sheet steel is cut and bent into the machine component shown. Knowing that the…

A: Density of steel ρ=7850 kg/m3 The thickness of the steel sheet t=4 mm

Q: What is the ideal mass flow rate for a refrigeration and cryogenic plant for oxygen production?

A: Ideal mass flow rate: Ideal mass flow rate is referred as the rate at which a fluid flow through a…

Q: Water flows in a 100 mm (4 in.) commercial steel pipe at 15°C (59°F). If the center velocity is 1…

Q: Question #2 (a) Calculate the total thermal resistance per unit length of tube for a 10 mm diameter…

Q: Determine the equivalent force system at the support O using the scalar analysis method. (the…

Q: What are the coordinates of A,B,C,D, if d=10ft? What are the lengths of the three ropes? X 135° 1 ft…

A: To find the co-ordinate of A B C D and find the length of the ropes

Q: Determine the reactions at the fixed support A of the beam. (the beam weighing 10 kN)

A: Given data:- the beam weighing= 10 kN To find:- the reactions at the fixed support A of the beam

Q: Air enters a turbine at 900K and leaves at 300K. The turbine shaft is connected to a generator with…

Q: For the given state of stress, determine the planes with compressive normal stress equal to 15 MPa.…

Q: 6.8 A load of lumber weighing W = 25 kN is being raised by a crane. The weight of the boom ABC is 3…

Q: An M/M/4 system has an arrival rate of 15 customers per hour. Each server has a service rate of 9…

A: Given: The arrival rate of customer per hour is λ=15 customer per hour. The service rate of customer…

Q: Problem 2: Determine the equations of motion for the system shown to the right in terms of the given…

Q: Determine the temperature, in °C, of Butane at 30 bar and a specific volume of 0.026 m³/kg. Hint -…

A: The pressure of butane P=30 bar The specific volume V=0.026 m3kg

Q: 8.50 and 8.51 Two 6° wedges of negligible weight are used to move and position the 900-kg block.…

A: For solution refer below images.

Q: The assembly shown below with M8x1.25 bolt/nut is subjected to an oscillating force F that changes…

A: Bolt- M8x1.25 n = 2σa = 48 MPaKc=1017 MN/mKb=346 MN/m

Q: Determine the distance H from the bottom of the base to the mass center of the bracket casting. 3.5"…

A: Given-Information:- To-Determine:- Distance, H¯ Diagram:-

Q: 2 m 8 KN 2 m 3 kN/m -4 m 2 m B

Q: 7-19 A heat engine with a thermal efficiency of 45 percent rejects 500 kJ/kg of heat. How much heat…

A: Thermal efficiency of the heat engine,(η)=45% The heat rejected,(QR)=500 kJ/kg Determine the amount…

Q: Consider an artificial boundary layer flow past a flat plate. The profile of the velocity field…

A: Given data:- Velocity profile uU=yδ1.2 for 0<y<δ uU=1 for y≥δ To find:- the displacement…

Q: A closed-cycle gas turbine unit operating with maximum and minimum temperature of 760 ⁰C and 20 ⁰C…

Q: A 150 mm horizontal waterline contracts abruptly to 75 mm diameter. A pressure gage 150 mm upstream…

A: Given:Upstream waterline diameter, d1=150 mm=0.15 mDownstream waterline diameter, d2=75 mm=0.075…

Q: Two billiard balls of masses m,-0.45 kg and m₂-0.50 kg are initially at rest. A cue gives the…

Q: A 78-tooth spur gear is in mesh with a 27-tooth pinion. The pd = 6 and ϕ = 20°. Find the contact…

A: Given: The Number of tooth on spur gear TG=78. The Number of tooth on pinion TP=27. The pitch circle…

Q: Determine the angular acceleration AB (positive if counterclockwise, negative if clockwise) of link…

A: The angular velocity of OB is θ˙=0 The angular acceleration of OB is θ¨=3.3 rad/s2 The angle is…

Q: hat tasks are completed prior to weighing an aircraft to determine its empty weight?

A: According to the question We need to find Empty aircraft weight by tasks are completed prior to…

Q: A gas furnace has an efficiency of 75%. How many BTU will it produce from 1000 BTU of natural gas.

A: Efficiency= 75%=0.75 Natural gas heat= 1000 BTU

Q: Figure (a) с (b) 1 of 1, B ▼ (FAB) a = Submit Part B 15| ΑΣΦ (NC) = Request Answer 11 vec t…

Q: Example 6.2. In Figure 2, a force of F = 250 N is applied to the end at B. Determine the speed of…

A: The force F=250 N

Q: Consider the area shown in (Figure 1). Suppose that a=h=b= 160 mm. Figure < 1 of 1 - Part A Locate…

Q: Consider the boundary layer flow=1-(1-)1.5, 0<y<8 and = 1, y ≥ 6. Using the von Karman momentum…

A: Given: The boundary layer flow is uU=1-1-yδ1.5. The Karman momentum integral equation is τw=ρU2dθdx.…

Q: What is the S-N Wöhler diagram, what is it for, how is it drawn? What is the Smith Diagram, what…

A: To explain: According to question need to explain- What is the S-N Wohler diagram, what is it for ,…

Q: Find the reactions at the hinge support at A and roller support at D of the truss shown. P=200N.

Q: 9- Find the moment of inertia about region bounded by the curve y = 6x - x² and the x axis

A: To find: The moment of inertia. Given: The region bounded by the curve y=6x-x2 and the x- axis.…

Q: What stable processes (phase changes) occur below 1400 o C? Give a good explantion

Q: A countershaft carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a…

A: T2=0.15T1 dB=300mm dA=250mm θ=45o To find: The tensions in the belt on pulley B The magnitudes…

Q: A force F is applied to the mass m₂ in Figure 1, where k₁ and k₂ are the spring constants, b₁ is the…

A: Given Data: System is given as Find: Transfer Function X1(s)F(s)

Q: A system executes a power cycle while receiving 750 kJ by heat transfer at a temperature of 1500 K…

A: According to the given data Q1=750kJ T1=1500k Q2=-100kJ T2=500K T3=1000K σcycle=0.1kJ/K We need to…

Q: 15.41 The motion of rod AB is guided by pins attached at A and B which slide in the slots shown. At…

Q: 3) What are the flow Q and the velocity V when total head loss is H = 25 m? KENTRANCE = 1.0 KGLOBE…

Q: find the moment of inertia about the y-axis for the shaded region

Q: A thin cylindrical vessel of 2 m diameter contains a particular gas at a pressure of 1.65 MPA. If…

A: To find: The value of minimum thickness required for the thin cylinder. Given: The value of diameter…

Q: Part G Identify the support reactions on the beam shown in Figure 4). The beam is supported by the…

A: According to the question We need to find Number of reactions of the beam ABC

Q: Determine the location of the sweet spot of the bat shown in the figure (Figure 1). The linear mass…

Q: A horizontal rough pipe of 150 mm diameter carries water at 20°C. It is observed that the fall of…

A: The pressure drop along the pipe : ∆pL=184 kPa/100 m The flow rate of water , Q=60 l/s The…

Q: Let the applied force on wedge B be: F1 = 3450 lb. Let the angle between the wedges be: 0 = 14°. Let…

Question

A heat engine receives heat from a heat source at 1200°C and has a thermal efficency of 40 percent. The heat engine does maximum work equal to 500 kJ. Determine the heat supplied to the heat engine by the heat source, the heat rejected to the heat sink, and the tmeperature of the heat sink.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Calculation

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

A water fountain is designed to cool water initially at 22.8∘C to a cool 7.7∘C at an average rate of 47 L/hr. It is expected that the water reservoir will absorb 46 W of heat from the surroudings. The refrigeration system has a COP of 1.79. (Assume the water has a constant specific heat.) What is the rate of heat absorption for this water fountain?
Determine the COP (coefficient of performance) of a heat pump if the rate of heat rejected is 360 kJ/min and power supplied is 2 kW.
Completely solve and box the final answers. A Carnot heat engine with a thermal efficiency of 70% is supplied with heat at a rate of 800 kJ/min. If it is coupled to a Carnot heat pump to deliver 1800 kJ/min per minute of heating, determine the COP and temperature outside the house if it is maintained at 24°C
A heat engine has a total heat input of 1.3 kJ and a thermal efficiency of 35 percent. How much work will it produce?
A heat pump is used to heat a house during the winter. The house is to be maintained at 20 C at all times. When the ambient temperature outside drops to -10 C, the rate at which heat is lost from the house is estimated to be 25 kW. What is the minimum electrical power required to drive the heat pump?
A solar energy based heat engine which recieves 90kJ of heat at 900C and rejects 70kJ of heat to the ambient at 200C is to be designed. Determine the thermal efficiency of the heat engine.
A heat pump keeps the house at 20°C while the ambient (outside) temperature is 0°C. from the roof and The heat loss from the walls is 3000 kJ/h per degree temperature difference between the indoor and outdoor environment. Determine the minimum theoretical power in kW required to operate the heat pump.
A heat engine accepts heat from a source at a rate of 500 kW, and it rejects heat to a sink at a rate of 300 kW. The remainder of the heat is converted to net work output. Determine the thermal efficiency of the engine
A heat engine receives a heat-transfer at the rate of 2 MW at a high temperature of 750 °C. The engine releases energy to its surrounding at 300 K and work is produced at a rate of 1200 kW. What are 1. The energy released to the ambient surroundings? 2. The efficiency of the engine?
The maximum efficiency of a heat engine works between 660 K and 323 K is
A heat engine that propels a ship produces 500 Btu/lbm of work while rejecting 300 Btu/lbm of heat. What is its thermal efficiency?
A heat pump with a COP of 3.2 is used to heat a perfectly sealed house (no air leaks). The entire mass within the house (air, furniture, etc.) is equivalent to 1200 kg of air. When running, the heat pump consumes electric power at a rate of 5 kW. The temperature of the house was 7°C when the heat pump was turned on. If heat transfer through the envelope of the house (walls, roof, etc.) is negligible, the length of time the heat pump must run to raise the temperature of the entire contents of the house to 22°C is (a) 13.5 min (b) 43.1 min (c) 138 min (d) 18.8 min (e) 808 min