he pin‐connected assembly shown in Figure below consists of solid aluminum [E = 70 GPa] rods (1) and (2) and solid steel [E = 200 GPa] rod (3). Each rod has a diameter of 16 mm. Assume that a = 2.5 m, b = 1.6 m, and c = 0.8 m. If the normal stress in rod (1) must not exceed 150 MPa, determine (a) the maximum load P that may be applied at A. (b) the magnitude of the resulting deflection at A.

he pin‐connected assembly shown in Figure below consists of solid aluminum [E = 70 GPa] rods (1) and (2) and solid steel [E = 200 GPa] rod (3). Each rod has a diameter of 16 mm. Assume that a = 2.5 m, b = 1.6 m, and c = 0.8 m. If the normal stress in rod (1) must not exceed 150 MPa, determine (a) the maximum load P that may be applied at A. (b) the magnitude of the resulting deflection at A.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Answer number 2 only
SIMPLE STRAIN
Mechanics of Deformable Bodies. Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that d1 5 30 mm and d2 5 50 mm, find the average normal stress at the midsection of (a) rod AB, (b) rod BC.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. One load of P=34 kips is applied to the assembly at A, two loads of Q=25 kips are applied at B, and two loads of R=37 kips are applied at C. The normal stress magnitude in aluminum rod (1) must be limited to 16 ksi. The normal stress magnitude in steel rod (2) must be limited to 32 ksi. The normal stress magnitude in brass rod (3) must be limited to 24 ksi. Determine the minimum diameter (in in rounded to the nearest thousandths) required for rod 2.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. One load of P = 30 kips is applied to the assembly at A, two loads of Q = 20 kips are applied at B, and two loads of R = 35 kips are applied at C. The normal stress magnitude in aluminum rod (1) must be limited to 15 ksi. The normal stress magnitude in steel rod (2) must be limited to 33 ksi. The normal stress magnitude in brass rod (3) must be limited to 22 ksi. Determine the minimum diameter required for each of the three rods. (1) R В D di in. d2 = i in. dz = i in.
At a point on the surface of a machine component the stresses acting on the e face of a stress element are or = 55 MPa and Txy = 30 MPa (see figure). T- 30 MPa a, = 55 MPa What is the allowable range of values for the stress oy if the maximum shear stress is limited to TO = 34 MPa? Round to one decimal place. (a) Lower limit is MPa (b) Upper limit is MPa
At a temperature of 27.89 °C a 0.41-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 126.64°C, determine the magnitude of the normal stress (in MPa) in the steel rod if L = 320.36 mm and M = 231 mm. Round off the final answer to four decimal places. d ... M A B Aluminum Stainless steel A = 2000 mm² E = 75 GPa a = 23 × 10-6/C A = 800 mm² E = 190 GPa %3D a = 17.3 × 10-6/°C
At a temperature of 28.42 °C a 0.4-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 137.38°C, determine the magnitude of the normal stress (in MPa) in the steel rod if L = 339.61 mm and M=240 mm. Round off the final answer to four decimal places. d ... В Aluminum Stainless steel A = 2000 mm² E = 75 GPa a = 23 × 10-6°C A = 800 mm² E = 190 GPa a = 17.3 × 10-6°C
Q1. An aluminum rod is rigidly attached between a steel rod bronze rod as shown in figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will n exceed a stress in steel of 90 MPa, in aluminum of 140 MPa bronze of 120 MPa. Aluminum Вronze A= 300 Steel A=100 A=200 ЗР 2P 5P 2.5m 2.0 m 1.5 m
3. The rigid bar ABC is pinned at B and attached to the two vertical rods. Initially, the bar is horizontal and the vertical rods are stress-free. Determine the stress in the steel rod if the temperature of the both rods is decreased by 30°C. Neglect the weight of bar ABC. Steel L=0.9 m A 300 mm E= 200 x 10 N/m' a= 11.7 um/(m C) Aluminum L=1.2 m A = 1200 mm E = 70 x 10 N/m a= 23 pum/(m "C) Answer: Ost B 0.6 m 1.2 m
Determine the normal stress and change in length of the aluminum rod if the temperature was raised by 125°C. The 0.5-mm gap exists at 20°C. q = 5 t = 0
i need the answer quickly