he crystalline density of polypropylene is 1.121 g/cm³, and its amorphous density is 0.906 g/cm³. What is the weight percent of the structure that is crystalline in a olypropylene that has a density of 1.054 g/cm³? elect one: a. 65 % b. 73 % c. 1.36 % d. 13.6 %

he crystalline density of polypropylene is 1.121 g/cm³, and its amorphous density is 0.906 g/cm³. What is the weight percent of the structure that is crystalline in a olypropylene that has a density of 1.054 g/cm³? elect one: a. 65 % b. 73 % c. 1.36 % d. 13.6 %

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter10: Liquids And Solids

Section: Chapter Questions

Problem 65E

See similar textbooks

Similar questions

Why is the C 60form of carbon called buckminsterfullerene?
An amorphous solid can sometimes be converted to a crystalline solid by a process called annealing. Annealing consists of heating the substance to a temperature just below the melting point of the crystalline form and then cooling it slowly. Explain why this process helps produce a crystalline solid.
NaH crystallizes with the same ciystal structure as NaCl. The edge length of the cubic unit cell of NaH is 4.880. (a) Calculate the ionic radius of H. (The ionic radius of Li+ is 0.0.95 .) (b) Calculate the density of NaH.
Use the phase diagram for sulfur for Question 75. The solid forms of sulfur are rhombic and monoclinic. (a) A triple point is defined as a temperature and pressure where three phases are in equilibrium. How many triple points does sulfur have? Indicate the approximate temperature and pressure at each. (b) Which physical states are present at equilibrium under these conditions? (i) 102 atm and 80 C (ii) 101 atm and 140 C (iii) 103 atm and 110 C (iv) 104 atm and 160 C Phase diagram for sulfur, for Question 75.
At 20. C the vapor pressure of white phosphorus is 0.0254 mmHg; at 40. C it is 0.133 mmHg. Use the Clausius-Clapeyron equation to estimate the heat of sublimation (J/mol) of white phosphorus.
Classify each of the following materials as falling into one of the categories listed in Table 12.2. What particles make up these solids and what are the forces of attraction between particles? Give one physical property of each. (a) gallium arsenide (b) polystyrene (c) silicon carbide (d) perovskite, CaTiO3
8.66 What structural characteristics are needed for additives such as plasticizers?
Identify the following substances as ionic, metallic, covalent network, or molecular solids: Substance A is malleable, ductile, conducts electricity well, and has a melting point of 1135 C. Substance B is brittle, does not conduct electricity as a solid but does when molten, and has a melting point of 2072 C. Substance C is very hard, does not conduct electricity, and has a melting point of 3440 C. Substance D is soft, does not conduct electricity, and has a melting point of 18S C.
Classify each substance in the table as either a metallic, ionic, molecular, or covalent network solid: Substance Appearance Melting Point Electrical Conductivity Solubility in Water X brittle, white 800 C only if melted/dissolved soluble Y shiny, malleable 1100 C high insoluble X hard, colorless 3550 C none insoluble
Phase diagrams for materials that have allotropes can be more complicated than those shown in the chapter. Use the phase diagram for carbon given here to answer the following questions. (a) How many triple points are present and what phases are in equilibrium for each? (b) Is there a single point where all four phases are in equilibrium? (c) Which is more stable at high pressures, diamond or graphite? (d) Which is the stable phase of carbon at room temperature and 1 atmosphere pressure?
The structure of graphite is given in Figure 12.19. (a) What type of intermolecular forces exist between the layers of six-member carbon rings? (b) Account for the lubricating ability of graphite. That is, why does graphite feel slippery? Why does pencil lead (which is really graphite in day) leave black marks on paper?
Materials containing the elements Y, Ba, Cu, and O that are superconductors (electrical resistance equals zero) at temperatures above that of liquid nitrogen were recently discovered. The structures of these materials are based on the perovskite structure. Were they to have the ideal perovskite structure, the superconductor would have the structure shown in pant (a) of the following figure. a. What is the formula of this ideal perovskite material? b. How is this structure related to the perovskite structure shown in Exercise 85? These materials, however, do not act as superconductors unless they are deficient in oxygen. The structure of the actual superconducting phase appears to be that shown in pan (b) of the figure. c. What is the formula of this material?