H(dB) A 20 ja `20 logio 11 +의 1 2 10 100 20 log101 1 20 log10 T1+ ja/10| 20 log10 Tja -20 Q.1) The phase (in degrees) at input frequency 100 rad/sec, if a zero is added to the above plot at input frequency 1000 rad/sec ? Note: this is a gain plot, you need to derive the phase from it! Q.2) at which input frequency (rad/sec) the plot is at unity gain ?

H(dB) A 20 ja `20 logio 11 +의 1 2 10 100 20 log101 1 20 log10 T1+ ja/10| 20 log10 Tja -20 Q.1) The phase (in degrees) at input frequency 100 rad/sec, if a zero is added to the above plot at input frequency 1000 rad/sec ? Note: this is a gain plot, you need to derive the phase from it! Q.2) at which input frequency (rad/sec) the plot is at unity gain ?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A- Calculate the total harmonic distortion for an output of power amplifier given by: V.-3+8sin 1000t+sin 2000t+0.5sin3000t+0.1sin4000t.
The weighted average system y(n) = 0.5x(n) + 3x(n-1) + 6x(n − 2) + 3x(n - 4). Sketch the block diagram for this system given the input signal x(n) = [0,1, 2, 3]. 1.2
Q- amplifier
Can anyone help me with this question
If there is a 20 percent over shoot in the frequency response, what is the corresponding magnitude of the second Minimum in the step response and the time at which it occurs. Take W1= 1.5 M rad/sec and W2= 0.2 M rad/sec.
1. The height of the response curve in a system depends only on the value of R. The width of the re- sponse curve is related to a defined quantity, the bandwidth. This relationship is expressed in terms of a very important parameter, the quality factor Q, which is represented by: a) Qo= 2nfoRC = woRC b) Qo= 2πRC = woRC c) Q₁ = 2πfo = woRC 2. Phenomenon that could occur in circuits containing Resistors, Inductors and Capacitors: a) Frequency separation. b) Filtering. c) Resonance. 3. A transformer, whose coupling is perfect (k-1) and the primary and secondary windings have no losses (R1=0= R2): a) Real Transformer. b) Ideal Transformer. c) Linear Transformer. 4. If both V1 and V2, are both positive or negative at the marked terminals, in the equation 2 = N₂ = n should be used: a) +n, (n positive). b) -n, (n negative). c) Any of the above. 5. A representation of the wave that shows the frequency content, but does not necessarily indicate the shape of the wave or the combined amplitude of…
B)- A transistor is used as an amplifier circuit at 8 GHz for which the S-parameters at reference impedance of 50 2 is listed below. Calculate the maximum power gain if the source impedance is 150 2 and load impedance is 200 2. S12=0.04 $21-2.15 $11-0.87 2-90 |$22-0.56 Z-45
I need the answer as soon as possible
Given the input sequence x(n)= 8(n)+2 &(n-1)+3 8(n-3) (a) Find 4-point DFT of the sequence x(n) (b) Calculate power in the signal and (c) Plot the power spectrum. 4 prove Parseval's relation
A filter is provided with a cascaded differential amplifier. The midband gain and noise coefficient of the filter are given as −3 dB and 3 dB, respectively. According to this, b) Find the noise coefficient of the cascaded system
Consider the BJT amplifer shown below. In the mid-band frequency range, we expect the input impedance Rin to be given by the expression: Vcc sig Rsig www Rin CB HH ww RB1 || RB2 | T RB1 RB2 (r +(B+1)RE) zero (due to CE) infinity (due to CB) RB1 RB2 (r +Rsig) RB1 Vb RB2 ww RC RE Cc HH ww11 CE RL
Question 1 Full explain this question very fast solution sent me step by step Not:- Text typing work only.