harges 100 efs of water. Determine the frictional loss of head per 1000 ft.

Q: Determine the internal force system acting on section 1 by analyzing the FBD of (a) segment AD; and…

A: Given Data  Find internal force system acting on the section 1 by considering a. Segment AD  b.…

Q: Q2B). Write construction and advantages of a windmill having high starting torque.

A: Answer IntroductionWInd mill works on the principle: The Energy of the wind rotates the blade around…

Q: a Determine the total head loss going from A to F b Determine the flowrates in pipes B – E

A: Discharge, QA = QF =96Diameter of pipes: DA = DF =4.5, DB =1,  DC =0.5, DD = 1.25,  DE =0.8Length of…

Q: 800 N. 2. The vertical bar is cantilevered to the floor as shown. Determine the moment of the loads…

A:

Q: Q#1: a. Analysis on canal section is carried out by technical team of WASA for a current water flow…

A: Given that:                  Discharge in the canal, Q=8000+2R=8000+2(58)=8116 ft3/sTemperature =…

Q: the level of water at A to maintain a constant depth of 11 ft. If the 50(10³) lb, determine the…

A:

Q: BD and Identify all the forces applied in the FBD

A: FBD AND MAKE 0

Q: This vent cover is fitted into a duct. a. How many inches high must the duct be?b. How many inches…

A: In the above image, the vent cover is fixed into the backward of the duct, the vent cover is larger…

Q: Q1: The figure below shows a regulator, determine whether the structure is safe against piping or…

A: Determine whether the structure is safe against piping or not and design the thickness of floor by…

Q: 19.9 Compute the design moment capacity of the preten- sioned beam of Problem 19.2 if f. 200,000…

A: Given, The yield strength of pre stressing steel fpy=200000 psi The nominal yield strength fpu=225…

Q: An wants Engineer to convert a tied rectangular column to a spiral column having H=500mm and…

A: Answer We are given  H = 500 mm b = 300 mm f'c = 21 Mpa fy = 276 Mpa As = 6-25 mm concrete cover c =…

Q: A soil element is shown in Figure 3 and 4, Determine the following: a) Maximum and minimum principal…

A:

Q: - Determine the magnitude and location of the resultant for the load system shown,

A:

Q: -36"-

A: Solution:- Neutral axis without compression steel, xu=0.87fy×Ast0.36fc×b…

Q: Determine the vertical reaction at A. Hinges at A and B are the same in elevation. 40kN 55kN B +50…

A: We have to use basic equation of statics in vertical direction. Summation of forces in vertical…

Q: Q1/Determine the reaction for The Con Beamy due to settlement of20mm) @suppor B-sto using slope…

A:

Q: Ql: The figure below shows a regulator, determine whether the structure is safe against piping or…

A: As per lane 's weighted theory-For no piping failure , HLw≤1C or  Lw≥CH             eq 1where, H…

Q: sticity and dimensions of a at the celerity of pressure wav ne pipe diameter is 1.2 m. and d 600 m.…

A: celerity of oressure wave , c =975m/sDiameter of pipe , d = 1.2 m length of pipe , l= 600 m velocity…

Q: Given QA, DA = DF , DB, DC, DD, and DE Pipes B-E are the same length (500 ft) If losses in the pipe…

A:

Q: From the given figure, compute for angle 0. Hinged, 6 m 1.2 m Wood 175-тт x 175-тт] (sg = 0.62) Sea…

A:

Q: Urgent, need correct answer as soon as possible with complete solution. Box final answer in 4…

A:

Q: 3m 3m 8 KN C D. 4m 1.5 KN Roller support 4m A 6 m

A:

Q: find Q ? and pressure at each pipe L. 7om dsolm Lsioum dso es fzoul

A:

Q: Determine the magnitude and direction of the hydrostatic force acting on the gate using PRESSURE…

A: Hydrostatic forces on surfaces deals with the fluids i.e., liquids and gases at rest. The velocity…

Q: 8) Three horizontal pipes, AB, CD, EF, laid in series, have the following properties: AB: L=200ft,…

A:

Q: A spherical gas-storage tank with inside diameter, d -6.5 (m) is being constructed to store gas…

A:

Q: Please answer with complete solution. Thank you!

A:

Q: Load Elongation o eng Eeng OTrue ETrue Lo |(mm)|(mm) F(KN)|SL(mm) No. Do 1 25 12.5 0.00 0.00 2 25…

A: Solution: From given table find the Stress and Strain; Engineering Stress/Strain:…

Q: 0. Im 0.3m hole I= 0.5m 0.3m 0.2m0.lm @ Find the reactions Ag By:. 40kft BA 4" 3

A: The centroid and distance of centroid is the area average for any section when any section have…

Q: 0.90m 0.25m 0.30m

A:

Q: A pressure vessel is constructed with an open-ended steel cylinder of diameter 6in

, length 8in

,…

A: Diameter of cylinder, Length of cylinder, Wall thickness, Bolt diameter, To find: Internal pressure.

Q: A cylindrical gate 10m long and 6m diameter is as shown. Assume that the cylinder does not rotate,…

A: GIVEN: Length of gate = 10m Diameter of gate= 6m Coefficient of friction=0.2 To determine:  Weight…

Q: Replace the system by a single force and determine its location from A. A 2 kip/ft 9 ft B 12 kip -3…

A:

Q: What pipe material will result in a friction factor of f = 0.014 for a 180 m long, 0.2 m diameter…

A:

Q: Two precast concrete sections of 224 [m] each are placed on a drawbridge, in such a way that they…

A:

Q: If a triangular gate of height 694 mm and base of 566 mm is vertical and submerged in c with its…

A: Height of triangular section = 694mm Base of Triangular section = 566mm Oil density = 800kg/m3…

Q: A copper cylinder 4in. inside diameter has walls 1in. thick. End plates are stayed by a 1in.…

A:

Q: Determine roller support reaction

A: Given data : The value of Point load P=15 KN The value of uniformly distributed load w=25 KN/m…

Q: Water flows steadily through the 1.0-in.-diameter galvanized iron pipe system shown in the Video and…

A: i hope its helpfull.

Pressure and Stress