HAB P В C MBC If the picture does not load, click here. Three blocks are positioned on an incline of 0=24° as shown. A force of P is applied to Block C and a wire attaches Block A to the wall, preventing that block from moving. The mass of Block A is ma=35kg, the mass of Block B is mg=53kg, and the mass of Block C is mc-47kg. The coefficient of static friction between Block A and Block B is HAB=0.18, between Block B and Block C is UBC=0.28, and between Block C and the ground is ucG=0.40. Determine the maximum value of P before any slipping takes place. Write your answer for P in N units to 2 decimal places in the box below. Hint #1: Recall that the shear (tangential) force across a sliding surface can never exceed F = mu * N Hint #2: You will need to find a value for P based on the condition that one block slips AND a value for P based on the condition that multiple blocks slip. The final answer will be the lesser of the two values. Values: HAB=0.18 ma=35kg 0=24° UBC=0.28 mB=53kg

HAB P В C MBC If the picture does not load, click here. Three blocks are positioned on an incline of 0=24° as shown. A force of P is applied to Block C and a wire attaches Block A to the wall, preventing that block from moving. The mass of Block A is ma=35kg, the mass of Block B is mg=53kg, and the mass of Block C is mc-47kg. The coefficient of static friction between Block A and Block B is HAB=0.18, between Block B and Block C is UBC=0.28, and between Block C and the ground is ucG=0.40. Determine the maximum value of P before any slipping takes place. Write your answer for P in N units to 2 decimal places in the box below. Hint #1: Recall that the shear (tangential) force across a sliding surface can never exceed F = mu * N Hint #2: You will need to find a value for P based on the condition that one block slips AND a value for P based on the condition that multiple blocks slip. The final answer will be the lesser of the two values. Values: HAB=0.18 ma=35kg 0=24° UBC=0.28 mB=53kg

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4) The figure below is a testing device used to measure the coefficient of friction between two materials (although it looks a bit like a record player). The disk is rotating at -20k rad/s and the length of the arm is 0.3m. At t = 0 the arm is put into motion with a rotational speed of 10k rad/s and the timer records how long it takes for the arm to reach a speed of rotation equal to that of the disk. Assume the elapsed time is 2.5 s. The normal force between the tip and the disk is 2N and lo = 0.015 kg-m2. a) Explicitly define the correct coordinates for the rotating system and write out the corresponding transformation array. b) Draw an FBD and IRD for the system. c) Calculate the coefficient of friction. [Ans. to Check: 0.3] d) Briefly explain what solution method you used to solve and why. Perspective view j Top view
Question 11: Figure 5 shows a lumped-parameter representation of a concept for a MEMS "tuning fork gyroscope" for measuring angular velocity. Displacements X₁, X2, and x3 are absolute positions of the respective masses and are measured from their static equilibrium positions where there is no deflection in the springs. The system friction is represented by three ideal lumped dashpot elements b₁,b2, and b3. Two external forces f₁ and f₂ are applied to masses m₁ and m₂, respectively. Derive the mathematical model of the MEMS gyroscope. x3 Leto, fi k₁ m3 k3 x1 m1 x2 m₂ f₂ b2
The figure shows a person wearing weight boots and doing lower leg flexion/extension exercise in a sitting position to strengthen the quadriceps muscles and a simple mechanical model of his leg. W1 is the weight of the lower leg, W0 is the weight of the boot, the magnitude of the pulling force applied to the tibia by the quadriceps muscles through the FM patellar tendon, the magnitude of the reaction force acting on the FJ tibiofemoral joint. Point O is the center of the tibiofemoral joint, point A is the point where the patellar tendon attaches to the tibia, point B is the center of gravity of the lower leg, point C is the center of gravity of the weight boot. The distances between point O and points A, B and C were measured as a=13 cm, b=27 cm and c=36 cm, respectively. The angle that the long axis of the tibia makes with the horizontal is β=34°, the angle between the line of action of the quadriceps muscle strength and the long axis of the tibia is α=18°. Points O, A, B and C lie…
a) A two-degree-of-freedom coupled pendulum model is shown in Figure Q1a. The parameters of the model are: k=100 N/m; m=10 kg and L=1 m. The equations of motion of the system are given below. J₁ä + (mgL + kĽ² ) 8₁ - kľ² 0₁₂ = 0 J₁₂+(mgL+kĽ²)₂-kĽ² 0₁ = 0 i) Calculate the natural frequencies. ii) Draw the mode shapes. m Figure Q1a. b) In the above system discuss the implications of the following changes in coupling stiffness. i) k is reduced considerably to 0.1 N/m. ii) k is increased considerably to 1x105 N/m. c) Draw a schematic of modal test arrangement of a beam using instrumented impact hammer. d) Why is it necessary to measure force in a modal test?
B- For the spring system given in Fig. B, Model the problem using Combine 14 element in ANSYS Mechanical APDL software, (With Screen Capture Step by Step) then, answer these questions: (Ki=1000 N/mm, K2= K4 = 500 N/mm, K=400 N/mm) (Fi=100 N, Fz=120 N). 1- Describe the element type that you used in the model. 2- Solve for the nodal displacements. 3- Solve for the reaction forces. ki 2 k2 F2 k3 www-wwwm 3 3 5 Fig. B
Q2: For mass-spring system shown. The mass is given an initial displacement x(0)= 0.1 m, and released from rest. Find: 1- The position of the mass after 2 seconds. 2- The velocity of the mass after 2 seconds. 3- Plot the response for three cycles and label the result from 1 & 2. 4- What is the period of oscillation? 5- What is the acceleration of mass (m) after 5 second? Į x(t) k=100 N/m m = 4 kg
You have a lever, 2m on each side, and four masses: 5kg, 10kg, 15kg and 20kg. You will place the blocks at different positions on the lever such that the two sides balance. Place each block a unique distance from the fulcrum. Use a torque balance to prove the system will not move.
Bonus Question: 8 Extra points A block of mass m = 1.0 kg is dropped from height h= 75cm onto a spring. The mass will attache to the spring and then the spring will compress. a). Find the spring constant if the maximum distance the spring is compressed is 10cm in following arrangement? ០០០០០០០០០ b). Find the maximum distance the spring is compressed in following arrangement if the angle is 30 degrees? You are using same spring. ss. mmmm 8
Please answer quick you are in a bumper car with a total mass of 200.0kg your friend is also in a bumper car with a total mass of 200.0kg.You are moving to the right at 1.00m/s. Your friend is moving to the left at 0.500m/s. Your car hits a spot on your friends car that has no bumper. Your bumper acts as a spring with a spring constant of 2.00x10^4N/m. Determine the velocity of your car when the bumper has raced a maximum compression of 0.0700m.Assume friction is negligible.
The mass attached to the end of a helical pull spring statically forces the spring to pull, and 100 mm static elongation in the spring references The same mass is attached to the end of this spring, and the mass is released vertically from a height of 0.6 meters how many times does the force on the spring increase according to the static loading state when it is released? 4.32 O 4.87 5.36 5.12 18110140 O 4.60
Write the global stiffness matrix of the spring assemblage shown. Assume that all springs remain horizontal, the vertical bars at nodes 2 and 3 are rigid and allowed to slide horizontally to the left or right. Node 1 K1 = 2000 lb/in K2 = 2000 lb/in Node 2 m K3 = 1500 lb/in K4 = 1500 lb/in Node 3 F = 250 lb ma K5 = 3000 lb/in Node 4
The mass of A is 39 kg and the mass of B is 9 kg .The coefficient of kinetic friction between A and the horizontal surface is u = 0.2. The constant force F causes the system to accelerate. The angle 0 = 22 ° is constant. (Figure 1) Part A Determine F. Express your answer with the appropriate units. HẢ ? F= Value Units Submit Request Answer Figure 1 of 1 Provide Feedback F • B.